Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer door wouldn't catch and stay shut
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Machine would not start and light stayed on with door closed.
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allow top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Wen the dryer gets hot but dry anything when it runs and no air comes through the filter opening with the filter out
First diagnose the problem. No air coming out the exhaust or filter, things aren’t drying, you can’t hear the blower running. Fuses or breakers are verified ok and on. Turn dryer off. Disconnect exhaust tubing after unscrewing it’s clamp. Drag the dryer away from the wall to get access to the back and unplug the 220 v power cable from its socket. Get behind the dryer to remove its back cover plate by unscrewing its holding screws with screwdriver or small socket wrenches. Vacuum out the back of the dryer removing the powdery dust around the blower motor and pulley and remove the old belt. Since there is no adjustment arm, you have to stretch the belt around the rim of the blower pulley with both thumbs pulling upward against the motor pulley below. After the belt is in place you can pull on it to be sure both pulleys rotate so the blower fan will rotate. Then just put the back plate on the dryer, replug it in, push it back enough to hook up the exhaust pipe and push the dryer back to its home spot. Turn it on and you’re ready to go. Then order a spare belt for the future in about 5 + years.
The latch on my dryer door wasn't working. I was having to shove a towel in the door to get it to stay shut until I was able to repair it.
All I had to do was get the model number off of the dryer and plug that information in online and within a couple of days the part arrived. It was great! There were directions that came with the part that explained how to replace the old latch with the new one.
I remember in the "olden days" when I would of had to call a repair guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.
We got a new timer, but it also did not work, so further checking showed that there was a fuse that was not working. We replaced the fuse and the new timer worked properly. Perhaps the trouble was the fuse rather than the timer, but we chose to just use the new timer.
We got the part so fast we were both surprised. My husband installed the part by just seeing how the old one came off. It was simple and fairly quick. Except that his hands are so big they had a hard time fitting in to where the part needed to go. Just opened the top of the dryer, took the old part out and put the new one in.
Broken door actuator spring -interposer for motor control
Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.
The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.
Received part in 3 days from ordering. I was surprised when it showed up at my front door so quickly. Less than 1/2 hour later we were drying laundry again. Very impressed with the speed of service and the price.
First removed 2 screws on lint remover vent. Used a screw driver to force up top of dryer from out front. These will require pressure to pop the top off the dryer. Once the top was up I could reach the actuator and remove the 2 screws holding it. Once removed just replaced with new actuator and bam, done. Snapped top of dryer back on and reinstalled 2 screws on lint vent and Done. Easy, no problem....Thank you PartSelect!!.
