Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replacing the dryer drum drive belt
Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.
Hi, I am a working mom, and my dryer quit just after it had been behaving strangely. At first, it kept spinning after the door was opened. It eventually stopped working, and I assumed that the door switch must be the culprit. I purchased the part from the catalogue, and watched the installation video. Repair: After unplugging the dryer and removing the lint screen, I used a philips head screwdriver to loosen and remove the two screws located at the lint trap. I then inserted a flat screwdriver into the area between the top of the dryer casing and the face. Per the video, at approx. 2 inches in from the left and right side. I did this while gently applying pressure from the back of the dryer top to the front. This loosens the clips allowing the top to be lifted back and out of the way. I then opened the dryer door and commenced loosening and removing the two screws that hold the dryer switch in place. I used my screwdriver to gently separate the wiring harness connection, as it also has a clip to keep the connection tight. With these items free, I simply popped the little black thingy back through the hole (The black thingy just keeps the slack in the wiring from sagging, I think). With the old part removed, I then installed the new part accordingly. I reversed my way back out of the process respectively. I plugged her back in, and turned her on. Back in business.
Wish it would have told us that when the front was removed the dryer drum falls.
Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.
the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.
First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
First of all my dryer would run with the door open. Then my dryer quit working completely. I noticed that the door switch was broken.
I remove the lint trap and the two screws that held the top down. Next to unscrew the two screws that holds the door switch. I prized the top up with a screwdriver . I unplugged the door switch and plugged in the new one. I inserted the switch into the door and replace the screws. I snapped the top back into place and replace the screws in the lint trap. I close the door and turn the dryer on and it worked. I followed the directions you provided on line. They were very easy to follow.
Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.
The friggin thing wouldn't shut off when you opened the door. The switch dealie was just hangin there like a loose tooth.
The videos showed the tech taking the front off the unit but my unit didn't play that game. Instead all I had to do was take the top loose, (don't forget to take the dryer vent screws out first, that was the first beer) then access to the switch was easypeezy. That coupling for the switch assembly was 2 beers long. Anyways, got it all back together and it works like it's suppose to.
The dryer just stopped working. Couldn’t get it to start.
Watched a you tube video that told me exactly how to do it. Saved us from going out and buying a new one. My husband and I were very proud of ourselves because just to get someone to look at it would have cost us $85. The part was only around $25.
First and foremost turn power off to dryer at main box. Next remove screws say lint filter, then gently pry right and left front corners up with putty knife. Raise top and secure. Disconnect switch wire by using flathead sliding in between connection. Next remove 2 screws under front opening to dislodge switch. Repeat process in reverse order...takes 30 min. tops...
This could not have been easier. The hardest part was tipping the dryer over on its' side. Instructions: 1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor. Insert leveling foot into the foot opening on the bottom of the dryer & screw in with fingers until it is difficult to turn. 2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level. 3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position. 4. Use a level, back to front & side to side, to determine if feet need further adjustment. 5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!