Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Although the motor was running, washer wouldn't agitate or spin.
After disconnecting the electrical supply, first remove the two screws at either end of the control panel and fold it back away from the washer top. Then, unplug the electrical lid switch connection. Now, remove the two clips at either end on top to disconnect the housing from the washer back and chassis. The motor is sandwiched between the water pump in the front and transmission at the rear. The Direct Drive Coupling connects the rear motor shaft to the transmisson. After you have taken the outter portion of the washer off, remove the two snap clips that hold the water pump in place and slide the pump off the front shaft. Best to also disconnect the upper hose connection so the pump can be moved out of the way. Caution though, remaining water in tub will drain out. Now remove the two screws that hold the clips in place which secure the motor to the transmission. Careful, as the old Direct Drive Coupling is probably destroyed, the clips are the only thing holding the motor in place and the motor needs to be supported so it won't drop to floor when the clips are removed. Be careful not to lose the four rubber grommets which sit between the motor and transmission bracket. After motor is on floor remove the old plastic slip-on direct drive coupling discs from both the motor and transmission shafts. The new replacement discs have steel centers which do not slide onto the shafts as easily as the old plastic ones did. I had to tap the center steel portion onto the shafts using a hammer and a deep wall socket the same width as the steel portion of the disc. Be careful! I'm sure that tapping the plastic portion of the disc to properly seat it on the shaft will break it away from the steel portion. In my case, It took me several attempts to completely seat the new discs. I had to do quite a bit of tapping to get the discs seated far enough onto the shafts so that the motor slipped easily against the transmission bracket grommets and the retainer clips snapped back into place easily. Reassembly is simply reversing the steps you took when taking the unit apart. Before putting the outter housing back in place, I checked to make sure everything was running smoothly by jumping out the electrical snap-in connection for the lid switch and running the machine in the spin cycle. Remember, if you don't jump out the lid switch and just try to test the unit in the aggitate cycle, the machine has to first fill with water.
popped thecap off removed the bolt, pulled agitator off replaced cogs(dogs) then put back together. works like new.whole time took about 10-15 min. saved my self 150.00 by not hireing repair man.
Top Half of Agitator would not function without appying sideways pressure
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remove black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Agitator was barely agitating. Making a clicking noise.
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Found directional gogs broken. Searched washer model # on PS.com and easily found schematic drawing. Received parts in a couple of days. Removed agitator with one nut, and other parts just pulled apart. Replaced the cogs and other parts which were not really broken....just worn. Everything went back together easily, and I was done! Parts Select saved me a LOT of time, and especially money, than if I had called a repair co. THANKS!
1. Watch the partselect.com repair videos for either of the following parts: Part # 3363394 (White Direct Drive Water Pump - two ports) or Part # 285753A (Direct Drive Coupling). 2. After disconnecting the washing machine from the wall, these videos will show you how to disconnect the frame off the washing drum from the front. Disconnecting the top panel is a little different: pull/pop the two end pieces off, and unscrew the screws. 3. Upon removal of the front frame (per videos), disconnect the electrical device from underneath the lid, using a phillips screwdriver and a nutdriver and/or wrench. Use a flathead screw driver for the clips to remove/replace the electrical wires. No need to splice/cut any wiring. 4. Put everything back together.
The movers broke both water intakes off flush with the back of the machine
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syphon to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
The biggest problem for me was finding the screws to remove the control panel. First there are two screws on the top back side of the control panel, then there are plastic covers that have to be removed from both sides of control panel, then you can remove the screws at the base of the control panel. Set the control panel back, then remove the golden brackets that hold the cabinet to back of the washer. The whole cabinet will come forward with a little coaxing. (Remember to put the screws with the part you have removed to make sure you put them back in the same place.) Next remove screws that hold on the lid switch, remove wiring from clips, then replace with new switch, situate wiring in clips, position switch into place, screw into place. The cabinet is really hard to get back into place, be patient it may take a few tries. Once you get the cabinet in place, replace the golden brackets, then place the control panel where the screw holes line up and screw down, replace plastic sides, then replace the screws in the back side and your done.
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
leaking drain pump. Obviously a common problem with this washer
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.
Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out. I respect that electrical parts are non-returnable as I am in the auto parts business.