Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Average Repair Rating: 5.0 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water and Ice dispenser quit working.
Turned off power at C/B panel. Took cover off dispenser, removed 3 screws, board held in by 4 screws. Removed all 4, replaced board after removing connecter. Put back together. Turned power on. Worked perfectly. 15 minutes max, part was $81, recieved 3 days after ordered.
James from Lakeland, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
22 of 32 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gary
September 19, 2019
The dispenser control board is not working. The temperatures of the fridge and freezer are showing and the ice dispenser is working but you cant change from ice to water or anything else buttons do not respond.
For model number lghs2665kf2
Hi Gary, if all the buttons do not respond likely the control board is faulty and needs to be replaced. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Marc
March 11, 2019
I have no power going to the "water dispenser control board". I was able to verify the power going into the "dispenser switch board", but can not decide which is bad. I replaced the ribbon that goes from "dispenser switch board" to the water dispenser control board". But still no power. Any suggestions on which board coud be out?
For model number GLHS66EJB0
Hi Marc,
Thank you for your question. Where there is no power going to the water dispenser board, you will need to replace that board. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Leo
August 4, 2018
Replaced water dispenser. No power off circuit board. What do i check?
For model number GLHS66EJW0
Hello Leo, Thank you for your inquiry. First check the wiring for any fraying or loose connections. Then we recommend checking the following parts: micro-switch, ribbon cable harness, water dispenser control board, and dispenser switch board. You can test the parts with a multimeter. Hope this helps!
Was this helpful?
Thank you for voting!
Nicol
June 26, 2019
Why does the ice always comes out from my ice dispenser
For model number phs37ehsb2
Hello Nicol, Thank you for the question. If ice is dispensing without pressing the paddle, I suggest checking the Flap, PartSelect Number PS1526427 for make sure it is not stuck open or warped allowing ice to fall through. It may also have an issue with the Ice Actuator, PartSelect Number PS1526394. Hope this helps!
When i press the extra ice button the door water dispenser comes on and off by itself.
For model number FRS6B5EEW1
Hello Ken and thanks for writing.
It is possible that the dispensing flap gets stuck at times and will cause this issue. There is a small spring the door spring # PS1526431 that over time weakens and needs to be cleaned or replaced. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
Mark
June 30, 2021
I have had trouble in the past but can’t remember why I was into this but I had to replace the ribbon between control’s to make ice and water in door to work again. Extra ice etc: I bought a new ribbon and did not fix it this time. Do I need to replace part 38a?
For model number FRS26LF7DS7
Hello Mark, Thank you for the question. If all of the controls are working but it will not dispense Ice or Water, you can Test the 38A Micro Switches. With a multimeter when the little button on top is pressed in it should read closed or beep if you have that option on your meter. If the Switches are good, you may need to replace the Water Dispenser Control Board. We hope this helps!
Was this helpful?
Thank you for voting!
Fred
March 2, 2024
This is in regard to the display board on the ice/water dispenser, your part PS1526494. I am studying the video to see if I can do this. In the video, the cable harness of the display board easily detaches; I do not have that kind of cable harness, mine is a very thin ribbon harness. Is there a video that shows how to properly release and re-attach that kind of ribbon cable? I'm afraid if I remove it by just pulling it out, I will not be able to get it back in.
For model number PHS37EHSB3
Hello Fred, Thank you for your inquiry. Sadly, we do not have a video for properly releasing the cable for this part, but most cables can easily be released using a flat blade screwdriver or putty knife against a tab on the connector. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.