Make sure you haven't got the discount earlier.
LED Display Board WPW10124269
Rated by 1 customer
Really Easy
15 - 30 mins
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
2) Removed the four screws holding the extension kit to the microwave (easily visible on the front of the microwave) and removed the side panels (required sliding the panels up and off).
3) Removed the six screws holding the microwave to the cabinet ... Read more (exposed after removing the extension kit)
4) Slide the microwave out and unplugged the cord from the outlet
5) Removed the screws that secured the front display panel to the microwave. These are located on the side of the microwave just behind the display panel. There are a total of 4 screws, 2 on each side. Additionally there was a clip holding the front panel on. We were able to press down to get it to release. NOTE: You will not be able to fully remove the panel as there are cables that run back to the board which is only reachable by removing the top panel
6) Removed the screws along the sides. back, and top to remove the top panel (there are 3 screws on each side and 2-3 in the back, there is only one screw on the top near the back right that holds the top to a part inside the microwave.
7) Peeled the top off of the microwave - there is a line of double sided tape that held the front of the top panel to the back of piece where the front display panel was mounted.
8) Carefully remove the existing LED Display Board. There is a single plastic clip that you have to very gently press back to slide the LED out. We were not careful enough and the clip broke. It did not hinder the replacement and even without the small plastic bit the LED board sat snuggly in its spot.
9) Trace the cable from the LED board back to the circuit board and unplug the cable. We pulled the cable out through the front of the microwave as the hole from the front display panel back to the board was just slightly too small to fit the board through.
10) The new LED panel arrived with extra boards attached to it. There were clear spots where the boards were perforated to easily snap off.
11) Thread the new cable from the front of the microwave through the hole and plug in where you removed the previous cable
12) Seat the LED Display Board in the slot.
13) Replace the top of the microwave and the associated screws (we used four small bowls to separate the screws for the top of the microwave, screws for the front of the microwave, screws for mounting the microwave, and screws for the expansion kit)
14) Reseat the front panel and replace screws
15) Plug microwave back in. (We took this opportunity to turn the breaker back on to test and make sure everything was working before we remounted the microwave)
16) Place microwave back in its mount and secure with mounting screws
17) Replace the extension kit if applicable and its associated screws.
-
Krystal from YORK, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
- < Prev
- 1
- Next >
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
3 people found this helpful.
3 people found this helpful.
1 person found this helpful.
- < Prev
- 1
- Next >
Manufacturer Part Number: WPW10124269
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.