Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft....
$6.21
In Stock
Order within the next 7 hrs and your part ships today!
The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle.
This part is black, made of metal, and around an inch in length. It i...
$3.99
In Stock
Order within the next 7 hrs and your part ships today!
This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending...
$3.99
In Stock
Order within the next 7 hrs and your part ships today!
This genuine black cap axle, also sometimes known as the dust cap, is around 2 inches in diamater and sold individually. Comprised of plastic, it is designed to keep debris out of the hub and axle of ...
$3.99
In Stock
Order within the next 7 hrs and your part ships today!
This ground drive fixed idler pulley is for lawn tractors.
910 inch offset
Ground drive fixed idler pulley helps apply tension to the drive belt, allowing the belt to turn.
Wear work gloves to...
$13.69
In Stock
Order within the next 7 hrs and your part ships today!
This flat idler pulley is a genuine OEM replacement part for use in outdoor power equipment. It is made of plastic and features a metal bore adapter, and a radial-style single row bearing. The pulley ...
$13.69
In Stock
Order within the next 7 hrs and your part ships today!
This OEM hardened washer spreads load under the bolts of your lawn tractor. It is silver, made of metal, and is sold individually. Over time, the washer may become damaged due to wear and fatigue, and...
$4.99
In Stock
Order within the next 7 hrs and your part ships today!
This ignition switch is an OEM replacement part found near the steering wheel or dashboard in lawn tractors and riding mowers. The switch has four symbols on the top side which indicate its various fu...
$14.93
In Stock
Order within the next 7 hrs and your part ships today!
E Ring Number 5133-75 is a black, metal ring for securing the position of other parts. If damaged it will become loose or fall off. Installation is rated as "Easy" and is done with a pair of pliers. R...
$5.29
In Stock
Order within the next 7 hrs and your part ships today!
Questions And Answers for TS142T
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat
... Read more other side.
ALL VIDEOS and the official Husqvarna instructions will tell you that you MUST remove both the mowing deck and the entire clutch pulley assembly to switch the transmission drive belt. This is NOT true. It takes some effort and tight maneuvering, but this job can be done relatively quickly without removing either. You do NOT have to rem
... Read moreove the mowing deck! You do NOT have to remove the clutch pulley assembly! What I did was to stand the tractor up nearly vertical, resting it against a golf cart I have and tying it in place for safety. Then, you have to loosen two black belt guides right by the clutch pulley assembly. I did NOT remove them, just left them hanging loose. Next, there is a silver bar that comes in from the outside of the mower chassis and attaches directly to the clutch, remove this entirely. Next, there is an electrical cord assembly in the way, trace this back, find where it plugs in, and unplug it. Next, in order to be able to slide the belt fully over the clutch pulley assembly, you have to take the mower deck belt off of JUST THE ONE spindle closest. I tie wrapped it in place after getting it off the spindle so that I could easily put it back onto the spindle as the last step when done. Once the mowing deck belt is off the closest spindle, you can then slide the drive belt completely over the clutch pulley assembly. You can then easily remove the entire drive belt, taking note (I took pictures) of how it is routed. Then, just reverse all of this. I began by fitting the drive belt over the clutch pulley assembly to make sure that end was correct. I then put the previously mentioned two guides, silver bar, and electrical cord back in place. Next, I shoved the belt down where it goes, working it down towards the transmission and routing it correctly. Of course, it is a little difficult with the limited space available, but I would rather do that then needlessly take the entire mowing deck off. You finally have to CAREFULLY slide it over the PLASTIC fan blades on the transmission. Once past those, it slides easily in place. The last step is to put the mowing deck belt that you previously removed and tie wrapped in place back onto the spindle. That's it! Only takes about 30-45 min. done this way.