Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the oven handle broke during delivery
I remove the damage handle from the oven door,Then i install the new door handle with no problem.The tools i used was a hand nut driver and a phillip #3driver.
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
I removed the oven door by unlocking the hinges and pulling out. Set on workbench (with towel/pad) and removed handle, four screws, then bottom and inside panel screws, then one nut to finally be able to get at the inner glass insert. Removed insulation and then took an extra hour to really clean all surfaces (middle glass was quite greasy due to inner glass being broken for a while. Reassembly wasn't bad, but took a while to figure out that the two thin 2" red spacers belonged around the two handle screws. This was tough to figure out as they come off when taking the handle off, but you can't see them, so didn't know where they came from! Anyway, if you're just a bit handy, you can do this job.
The bottom strip had become rusty and looking badly
I pulled the oven door off the hinges and took the bolts out of the bottom of the over that were holding the strip on. I then pulled the strip off and replaced it with the new on. I replaced the bolts and then replaced the door on the hinges.
I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.
I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!
We ordered the part from Part Select, got it within a week and replaced the door. It is a little tricky because one has to dismantle the entire door to do the repair (inside screw to undo). You'd preferably be 2 to do the repair, although one can manage.
Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot. 1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back. 2. Pop off the hemispherical glass cap. 3. Unscrew the old light bulb, and screw the new light bulb in its place. 4. Put the cap back. 5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Broken right END of oven door HANDLE (3 separate pieces assembled)
(Followed the ORIGINAL manufacturer's instructions for assembly we retained when purchasing the appliance.) Replacing the broken handle end involved removal of the LEFT handle end as well as the broken RIGHT end, the center rod handle, and unscrewing the outer door face from the inner door face. Had to find specialty screwdriver for non-standard screw heads. Sigh. It was impossible to replace the door handle, as it requires removing the entire door - It is too heavy for one person to hold in place while the 2nd person tried to blindly replace screws thru a 1/2 inch slit in the outer and inner door pieces. Hiring a handyman is impossible leading up to the holidays, so we decided to just buy a new stove. Something that should be really simple to replace for less than $50 is now a major budget outlay due to a crappy design.