Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
Parts That Fix Frigidaire Dishwasher FGID2466QF2A Leaking
Leaking is a commonly reported symptom for the FGID2466QF2A Frigidaire Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FGID2466QF2A Frigidaire Dishwasher that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
This dishwasher door gasket (Bottom Gasket, Gasket, Door Seal, Dishwasher Door Lower Seal) helps prevent water from leaking out of the bottom edge of your dishwasher door by creating a watertight seal. This part is attached to the bottom of your dishwasher inner door panel. It is frequently exposed to water and detergent during its lifetime. The water and chemicals can eventually wear down the gasket and compromise the integrity of the seal. If the gasket is malfunctioning, the integrity of the door seal will be effected. You will notice leaking through the bottom of your dishwasher door. If your dishwasher is leaking water from the bottom of the door, first inspect the seal for food particles near the bottom and sides, and remove the buildup, as it can stop the door from closing properly and keeping a tight seal; if not, you may need to replace the bottom door gasket. Check the door gasket for tears, cuts, or wear. This part is sold individually and measures 22.5 inches by 1.25 inches. It is constructed of plastic, and comes in yellow/grey. Includes one lower door gasket.
Replacing your Frigidaire Dishwasher Dishwasher Bottom Door Gasket
Customer Repair Stories
Leaking under door
Removed the door. Slipped off old gasket and replaced with new gasket. Replaced door and tried rinse cycle. Worked perfectly.
-
Ronald from Berwick, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Bottom Door Seal fell apart and started leaking.
-
Scott from Flowood, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing water leaking out. If broken, it should be replaced. Refer to your model number and user manual to ensure this part is right for you. When making this repair, open the dishwasher door and take out the lower dish tray for better access. Pull out the old gasket, and clean the channel with a rag. Push the new gasket into place into the notch on the door, which you should see upon close inspection, using a flat-head screwdriver for assistance if necessary. We do not recommend cutting any additional length off on the tub gasket if any is present during your repair.
Replacing your Frigidaire Dishwasher Dishwasher Tub Gasket - Gray
Customer Repair Stories
Dishwasher was leaking at the lower left side of the door.
Water leak solved...
-
John from Hummelstown, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
dishwasher was leaking water
-
Charles from Milton, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This splash shield kit is used in dishwashers and is attached to the lower front corners of the tub. The splash shield is used to prevent water from spraying past the door seal. If your dishwasher is leaking from the corners of the door gasket, replace this part. For this repair, the only tool needed is a flathead screwdriver. The measurements of this part are: 1.50 inches in length, 0.50 inches in width, 1.70 inches in height. It weighs 0.10 pounds. Remember to unplug your appliance from the power source as a safety precaution.
Replacing your Frigidaire Dishwasher Splash Shield Kit
Customer Repair Stories
Leakage under door.
-
Gary A. from Akeley, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Dishwasher leaking splash shield was cracked
-
John from WOODWAY, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, depending on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.
Replacing your Frigidaire Dishwasher Dishwasher Drain Hose
Customer Repair Stories
A hole in the dishwasher dicharge hose.
-
Lee from Columbus, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Drain hose was missing
-
John from Carthage, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
The tubing carries water from the water inlet valve to the tub.
Replacing your Frigidaire Dishwasher Dishwasher Water Inlet Tubing
Customer Repair Stories
Water fill hose leaked.
-
Thomas from Wheaton, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Old hose was split
-
Sandra R. from Groveland, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
This water inlet valve is for dishwashers. Water inlet valve supplies water to the dishwasher. Unplug the dishwasher and shut off the water supply before installing this part
Customer Repair Stories
Unit would not fill with water.
-
Cyril from WAYNESFIELD, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Dishwasher was not filling up at the start of the cycle.
Turned off the breaker for the dishwasher. Turned off the water supply valve. Unscrewed the screws in the panel that hides the parts under the dishwasher. Unscrewed the screws anchoring the dishwasher to the counter. Slid the dishwasher out about a foo ... Read more t. Inlet valve was located on the front left side of the dishwasher. Unclipped the wire harness. Placed a cookie sheet under the water line. Unscrewed the water line from the inlet valve. Unscrewed the two Phillips head screws holding the valve to the dishwasher frame. Got the new part. Put the screws back into the frame. Reconnected the water line and wire harness. Slid the washer back into place. Turned on the water valve. Watched for leaks. Turned the breaker back on and started the cycle. Watched for leaks. Once I saw there weren’t any replaced the screws anchoring it to the counter and replaced the cover on the bottom. That was it! Took me longer to type out the steps than it did to actually do the repair.
-
CHERI from CREEKSIDE, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Replacing your Frigidaire Dishwasher O-Ring - Front
Replacing your Frigidaire Dishwasher O-Ring - Rear
Water is supplied to the upper arm through this tube via the pump assembly.
Replacing your Frigidaire Dishwasher Water Supply Feed Tube
Customer Repair Stories
Leaking
-
Thomas from W HEMPSTEAD, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Wouldn't fix it
-
Carolyn from STILWELL, OK
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
Sold individually.
Replacing your Frigidaire Dishwasher Delivery Tube Gasket
Customer Repair Stories
Spinner fell off of delivery tube.
-
Jeffrey from Rougemont, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Dishwasher Leakibng
Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)
Followed delivery tube up side of dish ... Read more washer to top of tub and noticed reminents of where water ran down side of tub.
Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.
Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks
-
Eric from Benton, KY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Wrench (Adjustable)
This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwasher. No tools are required for this repair, simple remove the rack stops and upper dish rack, then disassemble the mount and spray arm before installing the new one.
Replacing your Frigidaire Dishwasher Upper Spray Arm
Customer Repair Stories
upper spray arm retainer nut failed
ordered new one from site, was delivered with-in 2 days ( with standard shipping) all 1 piece, took seriously 5 seconds to unscrew by hand and replace!
-
Michael from Hillsdale, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
The spray arm would fall off during the washing cycle.
-
Roy from Worcester, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This dishwasher heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher. NOTE: Brass nuts are NOT included. Must be ordered separately.
Customer Repair Stories
Heating Element was corroded.
-
Christopher from EVERETT, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
Heating element went out
removed the c-clips holding element underneath
and put new one in. Hard part was figuring out
what was holding the element but since I still
had the schematic drawing we figured it out.
Saved a bunch on a repairman. After watching
my friend install the new eleme ... Read more nt I could probably
do it myself next time.
-
Jane from Port Charlotte, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Sold individually.
This grommet fits on the spray arm of your dishwasher. This replacement part connects and seals the spray arm to the water hose that supplies water to the dishwasher tub. Be sure to shut off water supply to your appliance before completing this repair. This part is 3 inches in diameter and is off-white in color.
Replacing your Frigidaire Dishwasher Water Delivery Tube Grommet
Customer Repair Stories
Replacing grommet
-
Jack from KENDALLVILLE, IN
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers
wrong part
Now i am back at square one with part I don't need and hoping for the part I do need
-
Loraine from HYDE PARK, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
Water that fills your dishwasher lifts the float. When it reaches a certain level, the float triggers the float switch to shut off, thereby shutting off the flow of water into the dishwasher.
Replacing your Frigidaire Dishwasher Float Switch
Customer Repair Stories
machine was not filling
-
jon from northampton, MA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
No water to dish washer
-
steve from virginia beach, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
This lower spray arm is a genuine OEM part for various makes and models of dishwasher and is sold as an individual part. This part attaches to the lower spray assembly of your dishwasher and the lower spray arm itself clips into this part to facilitate its spinning movement during the washing cycle. To replace it, remove the spray arm by pulling it out, remove the surrounding circular clip and then twist to remove this bit. Made completely of plastic, this part measures approximately 3-inches deep, 2-inches wide, and 3.125-inches tall.
Replacing your Frigidaire Dishwasher Lower Spray Arm Support
Customer Repair Stories
missing bottom spray arm
-
Ashley from Normal, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
spray arm fell off and melted on element
-
Dale from Worley, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub. This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, Tappan, & Electrolux. Possible Repair Solution For: Not cleaning properly, unusual noises, leaking water.
Replacing your Frigidaire Dishwasher Lower Spray Arm
Customer Repair Stories
Lower spray arm attachment came off and melted
-
Thomas from SUN CITY, AZ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
The original lower spray arm has a blue circle sprayer that must have worn out and dislodged itself from the sprayer arm, it landed on the heating element and melted a bit!
-
Melissa from W LAFAYETTE, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
Customer Repair Stories
Dishwasher leaks
-
Gardner from Old Saybrook, CT
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
As water is filling your dishwasher, a float rises along with it. When the float reaches a predetermined level, it shuts off the flow of water, thereby preventing a leak.
Replacing your Frigidaire Dishwasher FLOAT
Customer Repair Stories
was brocken
-
Aleksandr from West Palm Beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Replacing your Frigidaire Dishwasher Door Hinge Kit
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the basket in the dishwasher is worn out or the basket is broken, replacing it can be a solution. No tools for this replacement are required, as it is an easy process. If you need further guidance refer to the instructions provided by the manufacturer. For safety precautions make sure to unplug the dishwasher and wear gloves.
Replacing your Frigidaire Dishwasher Silverware Basket
Customer Repair Stories
silverware basket skunked
-
Alan from Holley, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
large holes in the bottom of the basket where pieces of plastic kept breaking off
-
Lauren from Peabody, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This is an OEM center spray arm, which works with dishwashers.
Customer Repair Stories
The Center Spray Arm was broken
-
YVES from VALLEY STREAM, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This is the replacement detergent dispenser for your refrigerator. It is gray in color and is sold individually. It is approximately 8.5 inches long and 3 inches wide. The detergent dispenser stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end of the cycle, you may have a damaged or malfunctioning detergent dispenser. This is an OEM part sourced directly from the manufacturer.
Replacing your Frigidaire Dishwasher Detergent Dispenser
Customer Repair Stories
Leaked spot free fluid
-
Tim from MARINE ST CRX, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
The soap dispenser didn’t dispense the soap
-
Bernard from ACUSHNET, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers