Screw - 1/4-20 MCH HXW 5/8 S WH02X10237

jack from SANTA ANA, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench (Adjustable)

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Hub washer replacement

I noticed a loud noise during the spin cycle, I purchased a bearing, but after taking the washer apart, I realized that the hub was worn out, I replaced the bearing and other parts to put it back in running condition, it was a worthwhile job, and cost saving. I have to thank partselect for the helpful videos.

Other Parts Used:

Tub Seal

Split Ring

Inner Tub Base Hub

Dennis from NOBLESVILLE, IN
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Inner Tub Base Hub replacement

The tub base hub developed a large crack and spin started to make a large vibration. Agitator coupling was frozen, so I broke it by dremel, wedge (a minus driver) and a hammer. The hub nut was also frozen, so I cut two slits into the nut with dremel, then broke it into two with a wedge and a hammer. Once the hub nut was removed installing ... Read more

Read less

Other Parts Used:

Inner Tub Base Hub

Hub Nut

Tatsuhito from S HUNTINGTON, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Leaking shaft seal

This sounds like an easy fix to replace the shaft seal after watching the video, Oh how WRONG was I.....Firstly the video and parts list show just pull the agitator off..... NOOOOOO the bolt (Screw) is deep inside the agitator and that has to be removed to get the agitator off.....maybe in some models they have changed this poor design bu ... Read more

Read less

Other Parts Used:

Tub Seal

Agitator

Donald from SAINT JOSEPH, MO
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Socket set, Wrench (Adjustable)

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Noisy while spinning

I dissasembled the machine and it took about 30 minutes. Orderd the parts recommended for noisy spinning. Reinstalled the new parts / changed all drum straps. Cleaned the drain drum and spin drum and after complete reassembly the washer is still noisy in agitation and spin cycle. The motor,transmission,counter weight,and drum look ok but ... Read more

Read less

Other Parts Used:

Tub Seal

Split Ring

Thomas from SELAH, WA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Fin Broke off the Agitator

My wife washed a washable mop head and somehow it managed to break one of the fins off the agitator. I ordered a new agitator, fabric softener dispenser, agitator coupling, and bolt. I figured since I had to replace the agitator I would replace everything. This was super simple and easy. I watched a few videos on getting the agitator off ... Read more

Read less

Other Parts Used:

Fabric Softener Dispenser

Keith from STATESVILLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

7 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Agitator was not working during wash, would during end spin cycle

The worst part was removing the agitator. I finally found a thread that explained you have to pull directly up to release the 'clips' that held the agitator to the coupler. I used my kids' jumprope, tied around a thick, 4 ft. dowel, with the other end tied around the agitator fins. The key was making sure the rope was straight above th ... Read more

Read less

Other Parts Used:

V-Style Drive Belt

Heather from De Soto, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Agitator will not spin

Agitator would not spin and it was going to cost me I've a hundred soars for someone to come and fix it. I looked on this sight and found out what I thought was the problem and ordered four parts to fix it. I was amazed because they came in two days later. I started withe coupling which was the cheapest part and instaled it and it fixed ... Read more

Read less

Other Parts Used:

Agitator

V-Style Drive Belt

Jared from georgetown, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)

52 of 70 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Agitator came off of spline and broke

The bolt that held the agitator assembly on had sheared off. Had to drill out the old bolt out of the spline. After that, it was very easy. Just bolt the agitator assembly onto the spline and it worked like a charm

Other Parts Used:

Agitator Coupling Kit

Agitator

Michael from Lebanon Junction, KY
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

22 of 28 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Agitator in washing machine not moving

First, I removed the liquid softner dispenser cup from the agitator. Next I gripped the bottom of the agitator and pulled straight up. This was the most difficult part of the repair. Next, I removed the couplier bolt with the appropriate size socket wrench. And then removed the couplier from the transmission shaft. This exposed the sh ... Read more

Read less

Other Parts Used:

Agitator Coupling Kit