Get in touch, we're here to help!
Open until 12am ESTcustomerservice@partselect.com
Get this part fast. Average delivery time via standard shipping: 1.8 days.
Retaining Ring Specifications
How Buying OEM Parts Can Save You Time and Money
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Replacing your Maytag Dryer Retaining Ring
** I removed the Blower Housing which made the process much easier.
** Find a friend with or buy the snap ring pliers
** Big Secret not mentioned anywhere - the Motor Support (diag. #20) can be removed ! Hence - the entire Motor assembly can be taken out to remove those irascible Motor Clips.
** For the Green ground wire going from the dryer frame to the motor, you need to take the screw from the old motor and use it to screw into a hole marked with a black "slash" on the new motor.
** After 3 days of WD 40 and an allen wrench, I could not remove the Motor Pully from the old motor, so I would buy one if I were you.
** Hardest Parts - Removing the Motor Clips, reattaching the idler spring!, having another person hold the drum while I installed the Belt and reattached the front drum frame thingy, and deciphering my wiring schematic and reassembly diagrams ! That is why a digital camera is so helpful.
** The process is really very easy if you use the suggestions above and read the others.
** Find the "Model Diagram" on the PartSelect website - an excellent resource !!
** A twenty+ year old Maytag - up and running again !! Many thanks to others who shared their story.
1. Unplug the dryer power cord.
2. Removed the two screws at the bottom of the front dryer panel. Pull the bottom of the panel forward, which frees the retaining clips at the top of the panel.
3. Disconnect the two wires from the back of the panel, and remove the panel. The drum will be resting on the motor/blower hosuing.
4. Slide the belt off of the back of the tumbler, and remove the tumbler (have to angle it a bit, to clear the frame) and the belt.
5. Remove the thermostat cover (piece of angled sheet metal, in front of the blower unit).
6. Remove the screws from the blower housing, and lay it forward, to expose the blower wheel.
7. Remove the snap ring, and then the retaining ring from the blower wheel. Remove the old wheel.
8. Install the new wheel, then the retaining ring, and then the snap ring. Reattach the cover to the blower assembly.
9. Reattach the thermostat cover.
10. On the tumbler, drill out the rivets for each of the glides, and remove all glide parts. Install new glides.
This is a good time to complete any general cleaning inside the dryer cabinet, especially in the area of the motor. Since there is limited access to the motor itself, might help to use the blower function of a shopvac to blow out that dust.
Vacuum out all lint from around the felt drum seals.
11. Loop the new belt over the tumbler, and install the tumbler (the glides go towards the front of the dryer). Note: to keep the belt from falling off, I taped it to the drum with two pieces of painters tape..the blue tape that comes back off easily.
12. On the back of the dryer, remove the access panel, and complete installation of the belt to the idler pulley.
13. If you taped the belt to the drum....don't forget to remove the tape now. Reinstall front panel to dryer.
This was my first experience working with snap ring retaining rings. Even with snap ring pliers, they are difficult to remove without stretching them out. Be sure to order a new one with your blower wheel.
Also my first experience using a pop rivet gun ( to install the new glides). Found a rivet gun at Lowes for $9.99. Worked okay, and all rivets set properly. Good thing, because you don't get any extras with the glide kits.
After replacing the parts, and starting up the dryer, all of the clunking/squelling/rumbling noises were gone. There was a noticable smell while the new glides got broken in...smelled a bit like melting rubber. However, after a couple of drying cyles, the odor was gone.
Manufacturer Part Number: WP9703438
Get in touch, we're here to help!
Open until 1am ESTContact Customer Service