Models > 3KSM150PSTCU0

3KSM150PSTCU0 KitchenAid Mixer - Overview

Sections of the 3KSM150PSTCU0

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Retaining Ring – Part Number: WP9703438
Retaining Ring
★★★★★
★★★★★
(3)
PartSelect #: PS11746909
Manufacturer #: WP9703438
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$6.92
  In Stock
Order within the next 5 hrs and your part ships today!
Motor Brush – Part Number: WPW10380496
Motor Brush
★★★★★
★★★★★
(19)
PartSelect #: PS11753983
Manufacturer #: WPW10380496
Used on Stand Mixers. Sold Individually.
$11.69
  In Stock
Order within the next 5 hrs and your part ships today!
Worm Gear – Part Number: WPW10112253
Worm Gear
★★★★★
★★★★★
(32)
PartSelect #: PS11748374
Manufacturer #: WPW10112253
This worm gear is an inch and a half in diameter. It is used for some of Whirlpool's brands of mixers.
$22.68
  In Stock
Order within the next 5 hrs and your part ships today!
Flat Beater – Part Number: WPW10672617
Flat Beater
★★★★★
★★★★★
(30)
PartSelect #: PS11757063
Manufacturer #: WPW10672617
This has a powder coated finish.
$23.71
  In Stock
Order within the next 5 hrs and your part ships today!
Wire Whip Mixer – Part Number: WP9704329
Wire Whip Mixer
★★★★★
★★★★★
(15)
PartSelect #: PS11746928
Manufacturer #: WP9704329
This wire whip is for stand mixers. Wire whip attaches to the beater shaft and incorporates air into cream, eggs and frostings. Follow the instructions in the owner's manual for using and installing this part.
$30.50
  In Stock
Order within the next 5 hrs and your part ships today!
Foot – Part Number: WP9709707
Foot
★★★★★
★★★★★
(5)
PartSelect #: PS11747035
Manufacturer #: WP9709707
Sold individually.
$8.72
  In Stock
Order within the next 5 hrs and your part ships today!
Worm Gear and Bracket – Part Number: WP240309-2
Worm Gear and Bracket
★★★★★
★★★★★
(18)
PartSelect #: PS11740516
Manufacturer #: WP240309-2
Used for Kitchenaid Mixers.
$30.34
  In Stock
Order within the next 5 hrs and your part ships today!
Thumb Screw - Black – Part Number: WP9709194
Thumb Screw - Black
★★★★★
★★★★★
(14)
PartSelect #: PS11747009
Manufacturer #: WP9709194
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
$20.19
  In Stock
Order within the next 5 hrs and your part ships today!
Speed Control Plate – Part Number: WPW10119326
Speed Control Plate
★★★★★
★★★★★
(11)
PartSelect #: PS11748567
Manufacturer #: WPW10119326
Used in Mixers.
$20.56
  In Stock
Order within the next 5 hrs and your part ships today!
Retaining Pin – Part Number: WP9707223
Retaining Pin
★★★★★
★★★★★
(2)
PartSelect #: PS11746974
Manufacturer #: WP9707223
This part works in conjunction with the worm and bevel gear.
$8.72
  In Stock
Order within the next 5 hrs and your part ships today!
Transmission Case Gasket – Part Number: WP4162324
Transmission Case Gasket
★★★★★
★★★★★
(5)
PartSelect #: PS11742306
Manufacturer #: WP4162324
This part is used with Kitchenaid Mixers.
$18.08
  In Stock
Order within the next 5 hrs and your part ships today!
Speed Control Lever – Part Number: WP9709276
Speed Control Lever
★★★★★
★★★★★
(11)
PartSelect #: PS11747016
Manufacturer #: WP9709276
The speed control lever on your stand mixer allows you to adjust the speed that the mixer is running at. The lever is approximately 3.5 inches long, with a black plastic handle at the top. The speed c...
$9.80
  In Stock
Order within the next 5 hrs and your part ships today!

Questions And Answers for 3KSM150PSTCU0

Be the first to ask our experts a question about this model!

Common Symptoms of the 3KSM150PSTCU0

[Viewing 5 of 5]
Noisy
Fixed by
these parts
Show All
Touchpad does not respond
Fixed by
these parts
Show All
Takes too long to dry
Fixed by
these parts
Show All
Will not tumble
Fixed by
these parts
Show All
No heat or not enough heat
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Speed Control Lever KNOB BROKEN
Pulled the Knob off of the new Lever then pressed it on the old Lever. I had to order the whole lever because it was the part nearest the knob in the illustrated parts break-down. I RECOMMEND THAT THE KNOB BE ADDED TO THE ILLUSTRATED PARTS BREAK-DOWN.
Parts Used:
Speed Control Lever
  • Robert from Minot, ND
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
145 of 182 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer was making clunking sounds and shaking
I removed screws in a sequence that I felt wouldn't further damage the mixer until I had it completely unassembled. When I found the broken worm gear, I went online to find a part. I found an exploded view, but the part numbering was old, and the salesperson couldn't tell me what the worm gear and bracket assembly consisted of, as I only wanted the worm gear. After trying to drive the pin out of the assembly, and failing, I decided to back online and see if anyone else had a photo of the assembly. Luckily (and wisely) PartSelect,com did and that answered any questions I had. The price was better, too. Reassembly of the mixer was a cinch with the exploded view. It's working like new, and we're hoping for another 35 years of service from it! Thanks.
Parts Used:
Motor Brush Worm Gear and Bracket
  • Robert from Minden, NV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
80 of 86 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor would run but mixer wouldn't operate: broken worm gear
My girlfriends' stand mixer failed when the accessory drive cap fell into the mixing bowl and jambed the beater, spliting the worm gear. The teeth on this gear are made of nylon and are molded to an aluminum center. This part is designed to fail in situations like this, saving the more expensive transmission parts. Following a repair manual I found online, I first removed the rear cover and pulled out the cord strain relief out from the base. Next I removed the drip cup from around the base of the planetary drive. I then used a pin punch to drive out the pin holding the planetary to the center shaft and removed the planetary. The unit was then inverted and I removed 4 screws holding the bottom cover to the gear case, and the 5 screws from around the planetary drive. The bottom cover was then lifted off. Three screws holding the worm gear bracket in place were then removed and the worm gear assembly lifted out. A small pin holds the worm gear to the shaft. I drove this out with a small pin punch and the shaft and worm gear were then removed. There is also a thrust washer on this shaft, and it's location is important. Make a note for re-assembly. The new gear was installed and the entire process reversed for re-assembly. A successful repair completed! My girlfriend would have replaced this $200 appliance, but I was able to repair it for less than $30 including shipping.
Parts Used:
Worm Gear
  • Raymond from Shirley, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
75 of 78 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!