E23CS78HPS0 Electrolux Refrigerator - Instructions

pulled off the grill, emptied the door, unscrewed the hinge plate, lifted the door up and off, replaced the hinge parts, reinstalled the door. easy peasy. worked great. by the way. I received the parts by ups within 24 hours of ordering them online, standard shipping!

First off make sure you have a good quality Phillips screw driver. When the blade is worn out you can disassemble the ice maker with out removing the front. But to reassemble the front cover must be removed. Do yourself a favor and buy the drum and nut also. I am a mechanic by trade so the tools and repair was really easy. Be careful of the ice crusher BLADES they are very sharp. If your not mechanically inclined take pictures before disassembly, that will help you greatly. Hope this helps someone. Thanks Rory

Used a nut driver to remove the small panal from the back of the refrigerator. Removed the two screws holding the valve in place. Unscrewed the water lines from the old valve and cut the ends off of them. Push the water lines back into the new valve. Unpluged the wiring from the old valve and installed them in the new valve. reinstalled the new valve and put the cover back on. Tested system for proper operation.

Crusher housing had broken so I ordered the part and replaced it. I have since put it back together twice. When I first installed it it crushed the ice no problem. From that point on it seems to lock up and won't crush the ice, cube ice works but the blades seems to hang up after the first use. I can turn the cog by hand but I have to turn it backwards a few times before it turns freely, however it still won't crush the ice. I took it apart and put it back together again. Same thing happened after the first time I tried it. Can you help me. The old crusher broke into. Could something else be locking up?Thanks for the help

Had help with one person,to lift the door.But the part was easy to install.

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

simply took the screws out of the top of the door(after first emptying the door), picked it up off the bottom support and laid it on the counter. Used a needle nose pliers to remove what was left of the bottom bearing and replaced it with the new bearing. Placed it back on the support and put the top door mount back where it belonged. replaced the plastic hinge cover and it was as good as new. Really very simple.

removed 3 screws on top hinge plate. removed door and replaced hing bearing. reinstaled door.

So easy a cavewoman could do it!

took ice maker out empty ice removed 6 screws removed auger out took off lcck nut pulled off drum replaced with new drum reassembled.

I diagnosed the problem by checking the water flow at the supply valve and hose by disconnecting the hose from the back of the fridge. Found the pressure to be adequate. I then reconnected the supply hose and removed the cardboard backing from the fridge and removed the nuts holding the water inlet valve to the chassis. I loosened the first hose that runs from the bottom of the valve and had my wife activate the valve by pushing the water switch on the front of the fridge. Water basically sputtered out of the valve and I decided that was where the problem was. I ordered the valve from partselect. When it arrived I thought it was the wrong part because it had push-fittings whereas my original valve was all thumb screws. I took a chance and one by one used a utility knife to cut the hose free of the old valve as close to the nut as possible. Connecting them to the new valve was a piece of cake! Just make sure the hose bottoms out when you push it in. I turned the water back on, no leaks! Plugged the fridge in and pushed it back to the wall. After a bit of air bled out I had a strong flow of wateragain like new! The next day the ice cubes were solid again! We use the filtered water so many times a day and had been so frustrated with the slow water flow we had considered donating the fridge and buying a new one; thanks to this easy fix we expect keep it for years to come!

I followed a video I found on how to take the front off of the ice dispenser ( to me the hardest part) Once I was in there it was a matter of removing the pin and spring,then putting the new flapper in place of the old. Hardest part in reassembling was getting the spring back where it belongs. After that it was a matter of putting the ice dispenser back together and testing. Works perfectly.

Remove 4 screws to get the housing cover off. Remove the lock ring that holds the ice auger in place. REmove 4 screws to get the crusher housing off. Reverse the order to replace the housing. Very simple.

Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

It went okay. My husband did the job and he is handy. We both watched the little "How to" video and that was very helpful.