E23CS78HPS0 Electrolux Refrigerator - Instructions

removed backing to refrig unscrewed 2 screws from bracket pulled unit out unhooked hoses and elec plug's / putting in new just reversed the instalation

Remove crisper and shelf. Use a small punch and hammer to gently push the tightening pin through to the wall of refrigerator, keep in mind you'll need to remove this piece with small needle nose pliers before installing new part. Set new part in place and lightly tap the pin in until flush. Install crisper and enjoy the rest of your day.

My part had threaded fittings. The part that I received had snap fittings. Once I realized that that snap fittings worked with the bare tubing and not any special tip endings, I simply cut off the ends of my tubing that mated with the threaded fittings. I then had bare tubing that snapped into the snap fittings. Two minutes later, the part was in place and the job was done. Problem solved.

Removed broken cover frame and drawer.: saved unbroken glass .With putty knife removed two front broken support clips.Inserted new support clips installed new ,cover frame installed drawer replaced glass cover and turned refer over to wife.

Cut the 2 wires going to thermostat and connecting the new. Then connect the thermostat to same place I unhookef the old one.

Watched the video....it was perfect. Just needed a Phillips screwdriver, needle-nose pliers and a 3/8 socket. The cam was shattered, so I had to pull it out the old, broken one with the needle-nose pliers. The whole thing took about 20 minutes. Really appreciate that video!

Had a leak every night from refrigerator couldn't understand where from. Went on line and found some articles. I was referred to this sight by ads the articles and then in how to. I was pleased that a customer wrote their own instructions on what to do it was more concise clear and made preparation easier. First label towel cup and bucket needed too. Turn off water supply and electrical cord unplug then remove cover behind refrigerator vacuum and clean then. Water makes a mess so clean dry first. Then mark your hoses to remember order. Next remove old inlet and put in bucket it's pressure clamps so push in and it locks I chose to suction pipes and check for damage to pipes pin holes etc next I inserted into new inlet in order. At that time I turned water valve on checked for leaks at initial insert and new inlet. Next I plugged in unit cord. Waited. No leaks so far left for 30 minutes ran ice machine and water dispenser waited 20 minutes no leaks yet. Unplugged refrigerator unit. Installed the inlet completely to base and closed back paper panel after wiping water. Waited 24 hours then smiled no leak. Job done so far 2 weeks all clear. Hope this helps you will need screws driver and wrench for copper or main line I did find same part for less but this sight help me with good instructions the one they provide is for engineers architects lol not me I'm DYI

Remove the door. Remove the closer plate from bottom hinge install new closer plate. Remove hinge bearing from door install new hinge bearing. Reinstall door. Very simple procedure.

removed contents from refrigerator door I then used a Phillips screw driver to retire plastic cover off of top hinge bolts, then I used a nut driver to remove hinge bolts. after hinge bolts were removed I pulled the door off removed old bearing replaced with new bearing and then repeated the steps in reverse simple. Very far delivery with standard shipping.

This was one of the best internet purchasing experiences we have had. Certainly the convenience of ordering the part, speed of delivery, and "how too" instructions were fantastic. Unfortunately, the hinge bearing (PS976452) was diagrammed with the door and the closer plate (PS976594) was diagrammed with the refrigerator. You don't recognize you need both parts until you take the door apart. This necessitated two orders and two shipping charges and taking the door off twice. It would have been better if the whole hinge assembly had been diagrammed together. The fact that the second part was here in 24 hours even with standard ground shipping still made this an excellent experience. Works great. Thank you.

1) cleared remaining parts of broken crisper supports by pushing them into refrigerator insulation(pushed on 'pegs' so 'peg' holes in side of plastic inner liner of refrigerator were clear. 2) Was unable to fully place new crisper supports into postiion. 3) Then, out of despiration, used small light hammer to gently tap on largest 'pin.' I was surprised to see this 'pin' enter into plastic side of refrigerator and then to see crisper support was secure when 'pin'/peg' was flush with new crisper support. 4) then returned crisper to correct postion; supports held. 5) WARNING-DO NOT OVERLOAD CRISPERS!! I BELIEVE THIS CAUSED 'PIN'/'PEG' FAILURE INITIALLY! I don't know if cause was volume too high with crisper forced into place OR if the crisper mass/weight was the culprit. SUGGEST weight limit less than 7.5 lbs.; don't attempt to load in more volume than top of crisper.

I first determined the problem. I found PartSelect.com through online search. I ordered the part online Sunday morning. Part arrived Tuesday afternoon(Christmas eve) and I installed it that night! Now I am a gal mind you, but I am pretty handy. I pulled out the fridge, unplugged it and removed the back panel, easy. Then I used a heat gun on low the defrost the 'defroster' which had REALLY iced up bad. It had iced up so much,in fact, it had disconnected the evaporator fan connection. I clipped the wires. Stripped the ends, slid on the shrink tubing supplied, connected the wires with the crimp connectors and heated the shrink tube. I also put another piece of shrink tube on the fan connector so it would be more secure. Put the panel back on, plugged it back in and started working like a champ!! I am so proud of myself and likely saved at least $250.00 on a service call! Total cost for this repair, $22.00!! :D

This was the first time I ever installed a water inlet valve in a refrigerator. I viewed the Parts Select youtube repair video that is available online. In fact, I viewed it a couple times. Ultimately, the actual installation of the water inlet valve went exactly as shown in the youtube video. I did not experience any problems with the installation and was quite happy with the experience.

1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.