Range Ignitions
Find your part
Enter your model number or a part number and click "Search"Popular Range Ignitions
Your Price
$60.55
Spark Ignitor
PartSelect Number PS11728608
Manufacturer Part Number 808608802
The function of the ignitor in your range is to create the spark that ignites the gas on the burners. If your spark ignition system is not functioning properly, you may need to replace the ignitor. This part is approximately 3 inches in length. The ignitor is located in the rear of the range, so you will need to remove the back panel in order to access it for this repair. Before beginning this repair, be sure that the gas valve for the range is shut off. You should also disconnect the power source to the range before you begin.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Colin from MORGANTOWN, WV
Stove pilot not clicking on any burner, oven works fine
Unplug the range. Remove screw to Take of the back panel on upper right corner. Unclip the old spark module, unplug the wires with the needle nose pliers and plug them into the new spark module same as the old module. Clip it on. Replace the back panel.
Read more...
Your Price
$78.18
Spark Module
PartSelect Number PS11775689
Manufacturer Part Number 5304508269
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Brian from DUDLEY, MA
Stove top spark module broken
Worst part was cleaning my disgusting stove, installation was easy, remember the positioning of the wires from defective module(take picture)
Read more...
Your Price
$59.34
Spark Module - Surface Burners
PartSelect Number PS2003170
Manufacturer Part Number 12001596
This part may differ in appearance, but functions same as original part. : This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
jonathan from Bryson City, NC
No spark at top burners, first one then eventually all 4.
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, located inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks!
Read more...
Your Price
$54.57
Your Price
$64.74
Spark Module - (4+0)
Installation went smooth and easy.
replaced the spark wire and re-assembled the burnners. very easy repair. replaced the sark generator though it didn't need it because I didn't want to un-assessemble the unit again at a later date. Read more...
PartSelect Number PS952864
Manufacturer Part Number WB13T10046
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Frank from Steilacoom, WA
Spark would not turn off.
Removed the burers using a torx wrench disconnected the spark wire then replaced the spark generator and the wire harness to the gas valves. Installation went smooth and easy.
replaced the spark wire and re-assembled the burnners. very easy repair. replaced the sark generator though it didn't need it because I didn't want to un-assessemble the unit again at a later date. Read more...
Your Price
$94.85
Spark Module
PartSelect Number PS2350722
Manufacturer Part Number 316135702
This spark module or range spark module, is used in ranges and ovens. The spark module monitors and controls the spark to ignite the surface burner in a range. It does this by sending a certain amount of current to the igniter to produce that spark. If you are not getting any spark to the igniters then it is best you replace this part with a new spark module. To repair, first remove the access panel at the back of your range with a 1/4 inch nut driver to take the screws out. Next, disconnect the power harness that connects the range to the power cord to access the spark module. Take wires off using needle nose pliers and pull the spark module off the range. Match and hook up the wires to the new part. Refer to the manual provided by the manufacturer for further installation instructions and guidance.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Earl from ALLIANCE, OH
Top burners were not lighting without a match
Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly
Read more...
Your Price
$51.90
SPARK MODULE 6+0 KIT
PartSelect Number PS11729094
Manufacturer Part Number WB13X26360
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Kenneth Charles from HARDYVILLE, VA
Center Burner Switch would not generate spark and one other burner would not light.
In order to get to the burner switch you must remove the top of the range. Removed the 2 screws in the front holding it down then tried to remove the burner mounting screws securing the burner holders in place. Of the 12 screws, 10 were frozen. The screws sheared when I tried to remove them. After removing the top, I removed the burner holders one at a time and drilled out the broken screws. I would have purchased replacements but the part was listed as unavailable. I removed the front panel which exposed the switches. I cut the wires of the defective switch and used heat shrink crimp connectors to connect the new switch. With the top off the ignition module in the back of the range is exposed. I popped the old one out, changed the wires to the new one, one at a time and secured the new one in place with wire ties as the mounting tabs did not line up. Reassembled the range top using new #8 3/4" stainless steel screws to secure the burner holders. Plugged it in, turned on the gas and voila all the burners light. What should have been a 2 hour job took about 10 hours due to having to drill out the sheared screws.
Read more...
Your Price
$123.23
Burner Spark Module - 120V 60Hz
PartSelect Number PS231281
Manufacturer Part Number WB13K25
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
David from Logansport, IN
Top four burners on oven would not light without using match
Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. There are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module.
Read more...
Your Price
$43.22
Cooktop Spark Module
PartSelect Number PS11761179
Manufacturer Part Number EBJ62730001
The spark module controls the spark for lighting the cooktop surface burners.
Your Price
$313.82
Spark Module
If you still want to know how to replace the spark module start by removing #24. This will allow the removal of #9 (after you take the knobs off). You may have to do some fiddling cause the rubber gasket is sticky. Next there are 2 obvious regular screws for #14 and 2 not so obvious star screws in the space where the burner valves are. After #14 is off there are 2 screws on the spark module to be removed and one that you can't loosen that is in a slot. You wriggle the module out of that one. Read more...
PartSelect Number PS11755329
Manufacturer Part Number WPW10475147
This is a 4-point re-ignition spark module. NOTE: This part has been redesigned by the manufacture, it may appear different but will still function the same.
Installation Instructions
Robert from Ranchos de Taos, NM
Burners kept clicking after ignited
This problem was driving me crazy for months. Of course, after I bought and installed the part and it still was not fixed I finally found a website that told me how to fix the clicking. The problem is that the removable head burners (#8 on the top assembly diagram) are not making good electrical contact with the base burners (#22). What I did was grab the head burners and grind them back and forth into the base burners with the weight on the heal of my hand. Steel wool or sandpaper would work too--you just want to clean the surfaces to restore electrical contact.If you still want to know how to replace the spark module start by removing #24. This will allow the removal of #9 (after you take the knobs off). You may have to do some fiddling cause the rubber gasket is sticky. Next there are 2 obvious regular screws for #14 and 2 not so obvious star screws in the space where the burner valves are. After #14 is off there are 2 screws on the spark module to be removed and one that you can't loosen that is in a slot. You wriggle the module out of that one. Read more...
