Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Paul P - September 1, 2021
Verified Purchase
Soak Module
Easy Repair. Works Great.
★★★★★
★★★★★
Michael S - December 18, 2018
Verified Purchase
Spark Module Replacement
Part came with detailed instructions that made replacement easy.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.4 / 5.0, 7 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
IGNITER INOP
REMOVE GRILL AND TOP OF BURNERS. CLEAN GUNK OUT OF TORQUE SCREWS AND TRIED TO REMOVE TOP PLATE. FOUND IGNITERS ALSO NEED TO COME OUT, THEY HAD HEAVY DEPOSIT, BE CAREFUL. ONCE I GOT THEM OUT, JOB WENT WELL. NOTE MAKE SURE ALL CONNECTION ARE CLEANED BEFORE REASSEMBLY.
First step is to turn off the electrical then disassemble the cook top. It is secured to pan by each of the burner mechanisms. Disconnect the spark wire from each porcelain drip pan. Separate the glass top from the pan. If it's stuck gently slide a putty knife int between the two to separate and carefully set the glass top aside. The spa
... Read morerk module was a bit challenging in that the colors of the wires didn't match so if you aren't comfortable with electrical work I would get help. The module didn't fit the bracket so,I had to drill new holes and use self tapping screws to mount it. The other part part I intended to change was the spark igniter switch. Unfortunately the wiring was incompatible so I had to return that part. This top was sold by Kenmore but made by GE and is over 10 years old so I suspect an engineering change obsoleted my part. Overall the job wasn't that bad if you are reasonably mechanical..
Removed the burers using a torx wrench disconnected the spark wire then replaced the spark generator and the wire harness to the gas valves. Installation went smooth and easy. replaced the spark wire and re-assembled the burnners. very easy repair. replaced the sark generator though it didn't need it because I didn't want to u
... Read moren-assessemble the unit again at a later date.
I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part onl
... Read morey coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks
Read less
VINCENT from CYPRESS, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
9 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
igniter wasn't lighting burner
Repair to range went real well, Lifted range from
counter. Removed eight screws that secure burner
assembly. Lifted burners from it's position, and
removed igniters. Installed heat srink at burner
connections so as to ensure high voltage would
have no leaks. Removed insulation, and
... Read moreinstalled
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Al
January 3, 2018
Igniter won't stop sparking after burner lites. Happens on all burners from time to time.
For model number JGP328BEC2BB
Hi Al, Thank you for the question. If it is all the top burners that are sparking, you will need to replace the Spark Igniter Switch and Harness Assembly, PartSelect Number PS953094. Hope this helps!
The back right burner (small burner) does not click/spark consistently, causing it not light. The other 3 burners work fine. Any ideas?
For model number JGP328SEJ1SS
Hello Kenny,
Thanks for your question. The spark module is the most likely cause for your issue, though it is also worth examining the spark igniter switch and harness assembly.
I hope this helps.
When i turn on the front right burner to ignite the gas flows and ignites but the clicking continues along with sparking from white ceramic thing.When i turn off the gas, the clicking and sparking continues. in order to stop it i must go to the breaker box and flip the switch off. here is my question. is it the spark module (ps952864) or is it the gas valve switch (ps 236791) that needs to be replaced? what do you think? thanks
For model number JGP930SED1SS (General Electric) cooktop
Hi Joel, thank you for your question. It could be either part. You would have to test both parts with a multi meter to determine if that part is the one that is not working. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Tim
February 11, 2018
Everything on the oven works but the broiler won't light. What are the most common possibilities. Also when the broiler is turned on and doesn't lite. I don't smell gas.
For model number Jgsp48
Hi Tim, Thank you for the question. Sounds like a defective igniter. If the igniter is weak it will not send enough volts to open the gas valve. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Douglas
November 16, 2023
When the other 3 burners are turned to ignite the main burner igniter operates.
For model number JGP940BEK2BB
Hello Douglas, thank you for the question. Based on our research, we would recommend checking the spark module, part number PS952864, to fix the issue. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Roger
March 18, 2018
When "a" valve switch was turned on, burner b was sparked. When "c" value switch was turned on, burner b was sparked. Or when "d" switch was turned on, burner c was sparked. Not all the burners were sparked at the same time. Not sure this is a problem with the spark module (ignitor) or with the spark ignitor switch and harness assembly? Any help will be appreciated.
For model number JGP932BEC2BB
Hello Roger, Thank you for your inquiry. The spark ignition switch and harness is more likely to be the problem, but you can test the individual switches with a multimeter to see if they have continuity. If one does not, then the spark igniter switch and harness assembly would need to be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tim Hardwick
September 23, 2017
My electrode keeps clicking. After cleaning the counter top i accidentally got one of the electrodes wet. After about 30 minutes it started clicking. I turned the power off at the breaker box because that was the only way to make it stop clicking. I waited a few days to let it dry and all four burners are still clicking. Help!
For model number JGP933SEK1SS
Hi Tim,
Thank you for your inquiry. If all the burners are clicking there could be excess moisture even though everything looks dry. You may have to remove the burner caps and at them air dry. If this does not help you may have to replace either the spark module or the spark electrodes. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Linda
December 27, 2019
Igniter switch will not turn off... the burner lights but clicking doesn’t stop... so i have to leave burner on or go crazy listening to it click
For model number JGBS66EEK2ES
Good Day Linda. Thank you for your question in regards to your unit (Model Number JGBS66EEK2ES). Based on our research, we discovered that one of the most common reasons a gas stove starts clicking is because the burner cap is out of alignment. In order to solve this issue, wait until the cooktop is completely cool, remove the burner grate to access the cap beneath it. Remove the cap and re-center it on the base. We would also recommend that you unplug your unit before you start this repair. Hope this helps. Best Regards.
Was this helpful?
Thank you for voting!
Robert
January 9, 2019
Sometime igniter clicks sometime not only one burner other three always click and light fine harness switch or spark module
Hello Robert, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
