The function of the ignitor in your range is to create the spark that ignites the gas on the burners. If your spark ignition system is not functioning properly, you may need to replace the ignitor. This part is approximately 3 inches in length. The ignitor is located in the rear of the range, so you will need to remove the back panel in order to access it for this repair. Before beginning this repair, be sure that the gas valve for the range is shut off. You should also disconnect the power source to the range before you begin.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Range.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Electrolux.
Part# 808608802 replaces these:
AP5987234, 316262401, 316262405
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Marvin A - November 17, 2018
Verified Purchase
Worked as expected
Not only did this part arrive within a reasonable amount of time, but it worked even better than I had predicted. My stove needed this and it might as well be good as new at this point.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Stove pilot not clicking on any burner, oven works fine
Unplug the range. Remove screw to Take of the back panel on upper right corner. Unclip the old spark module, unplug the wires with the needle nose pliers and plug them into the new spark module same as the old module. Clip it on. Replace the back panel.
Colin from MORGANTOWN, WV
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
15 of 22 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Archie
November 7, 2019
Burners don't light an oven don't light, no clicking on both. What to do???
For model number 79072402013
Hello Archie, thank you for your question. If the top burners are not lighting and the oven isn't lighting, we would recommend testing the spark module PartSelect Number PS11728608, and the oven igniters and the gas valve. I hope this helps.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Nancy
October 13, 2023
The spark igniter does not click but can light the burner manually. Oven starts and works just fine.
I figure it’s the spark module, am I correct?
Thank you fir your help!
For model number FFGF3023LBE
Hello Nancy, thank you for reaching out to PartSelect. If none of the burners are working and you are positive that it is getting power, then the only part that can cause this issue is the spark module, part number PS11728608. Good luck with this repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
