Kenmore Range Ignitions

Your Price

$69.72

Spark Module

★★★★★

8 Reviews

PartSelect Number PS11775689

Manufacturer Part Number 5304508269

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Brian from DUDLEY, MA

Stove top spark module broken

Worst part was cleaning my disgusting stove, installation was easy, remember the positioning of the wires from defective module(take picture) Read more...

Your Price

$65.25

Spark Ignitor

★★★★★

1 Review

PartSelect Number PS11728608

Manufacturer Part Number 808608802

The function of the ignitor in your range is to create the spark that ignites the gas on the burners. If your spark ignition system is not functioning properly, you may need to replace the ignitor. This part is approximately 3 inches in length. The ignitor is located in the rear of the range, so you will need to remove the back panel in order to access it for this repair. Before beginning this repair, be sure that the gas valve for the range is shut off. You should also disconnect the power source to the range before you begin.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Colin from MORGANTOWN, WV

Stove pilot not clicking on any burner, oven works fine

Unplug the range. Remove screw to Take of the back panel on upper right corner. Unclip the old spark module, unplug the wires with the needle nose pliers and plug them into the new spark module same as the old module. Clip it on. Replace the back panel. Read more...

Your Price

$59.37

Spark Module - 60Hz

★★★★★

2 Reviews

PartSelect Number PS11728607

Manufacturer Part Number 808608801

Your Price

$112.51

Spark Module

PartSelect Number PS11748331

Manufacturer Part Number WPW10110491

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Carolyn from Bellingham, MA

Top burners would not light. No "clicking" .

My husband and I replaced the igniter module, following directions we found online. We removed the old one, replaced it with the new one, and thankfully everything is working great! Read more...

Your Price

$57.02

SPARK MODULE 6+0 KIT

★★★★★

2 Reviews

PartSelect Number PS11729094

Manufacturer Part Number WB13X26360

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Kenneth Charles from HARDYVILLE, VA

Center Burner Switch would not generate spark and one other burner would not light.

In order to get to the burner switch you must remove the top of the range. Removed the 2 screws in the front holding it down then tried to remove the burner mounting screws securing the burner holders in place. Of the 12 screws, 10 were frozen. The screws sheared when I tried to remove them. After removing the top, I removed the burner holders one at a time and drilled out the broken screws. I would have purchased replacements but the part was listed as unavailable. I removed the front panel which exposed the switches. I cut the wires of the defective switch and used heat shrink crimp connectors to connect the new switch. With the top off the ignition module in the back of the range is exposed. I popped the old one out, changed the wires to the new one, one at a time and secured the new one in place with wire ties as the mounting tabs did not line up. Reassembled the range top using new #8 3/4" stainless steel screws to secure the burner holders. Plugged it in, turned on the gas and voila all the burners light. What should have been a 2 hour job took about 10 hours due to having to drill out the sheared screws. Read more...

Your Price

$61.79

Spark Module - (4+0)

★★★★★

2 Reviews

PartSelect Number PS952864

Manufacturer Part Number WB13T10046

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Frank from Steilacoom, WA

Spark would not turn off.

Removed the burers using a torx wrench disconnected the spark wire then replaced the spark generator and the wire harness to the gas valves.
Installation went smooth and easy.
replaced the spark wire and re-assembled the burnners. very easy repair. replaced the sark generator though it didn't need it because I didn't want to un-assessemble the unit again at a later date. Read more...

Your Price

$86.63

Spark Module

★★★★★

2 Reviews

PartSelect Number PS2350722

Manufacturer Part Number 316135702

This spark module or range spark module, is used in ranges and ovens. The spark module monitors and controls the spark to ignite the surface burner in a range. It does this by sending a certain amount of current to the igniter to produce that spark. If you are not getting any spark to the igniters then it is best you replace this part with a new spark module. To repair, first remove the access panel at the back of your range with a 1/4 inch nut driver to take the screws out. Next, disconnect the power harness that connects the range to the power cord to access the spark module. Take wires off using needle nose pliers and pull the spark module off the range. Match and hook up the wires to the new part. Refer to the manual provided by the manufacturer for further installation instructions and guidance.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Earl from ALLIANCE, OH

Top burners were not lighting without a match

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly Read more...

Your Price

$127.72

Burner Spark Module - 120V 60Hz

★★★★★

3 Reviews

PartSelect Number PS231281

Manufacturer Part Number WB13K25

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

David from Logansport, IN

Top four burners on oven would not light without using match

Really simple..Opened the top of the oven and followed the four wires hooked to the igniters on the burners to the back of the oven. Unscrewed top section in back of oven. Found spark module screwed to uppper back of oven on right side. Used a nutdriver to take a few screws out of upper back of oven. Unscrewed spark module from oven. There are six wires - four to the burners and two to the power supply....Wires are attached by connectors so didn't have to do anything but pull the connectors off the old spark module one at a time and push them onto the new spark module matching postion of each wire. Screwed spark module back onto back of oven. Screwed back section of oven back onto rear of oven, and that was it. Works perfectly. Saved more than $100 for service call and whatever elevated price they'd charge me for the spark module. Read more...