My Orders
Kenmore Range Caps and Lids
GET YOUR OFFICIAL Kenmore PARTS TO ENSURE VICTORY
Popular Kenmore Range Caps and Lids
The surface Meduim 9.5K burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner head from cooking spills. Without the cap you can have a burning gas torch. If your cap is missing or is discolored, replacing this part can solve the issue. This part comes in the color black. Remember to unplug your range from the power source and allow surface to cool before installing this part. Refer to the manual provided by the manufacturer for further installation instructions.
The surface Meduim 9.5K burner cap is located on the top of the burner head and is used in ranges and ovens. The burner cap helps spread out the burner flame for even heating, and protects the burner head from cooking spills. Without the cap you can have a burning gas torch. If your cap is missing or is discolored, replacing this part can solve the issue. This part comes in the color black. Remember to unplug your range from the power source and allow surface to cool before installing this part. Refer to the manual provided by the manufacturer for further installation instructions.
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
This black burner cap is a genuine OEM part made of a durable material capable of reaching 14,000-BTU, with an approximately 3-inch diameter. It is compatible with various models of ranges and cooktops, where it helps to distribute heat evenly and protects the burner assembly from thermal damage. Since this cap is sold as an individual part, consider how many caps you need to replace on your stovetop before ordering. Burner caps often need to be replaced if they are damaged or worn, no longer providing even heat distribution, or if they simply no longer look good. To replace this cap, make sure the stovetop is cool, and then simply lift any necessary grates to get access to the cap. Then lift and swap out the old cap for the new one, making sure it is settled properly on the burner before you reseat the grate(s).
This black burner cap is a genuine OEM part made of a durable material capable of reaching 14,000-BTU, with an approximately 3-inch diameter. It is compatible with various models of ranges and cooktops, where it helps to distribute heat evenly and protects the burner assembly from thermal damage. Since this cap is sold as an individual part, consider how many caps you need to replace on your stovetop before ordering. Burner caps often need to be replaced if they are damaged or worn, no longer providing even heat distribution, or if they simply no longer look good. To replace this cap, make sure the stovetop is cool, and then simply lift any necessary grates to get access to the cap. Then lift and swap out the old cap for the new one, making sure it is settled properly on the burner before you reseat the grate(s).
A cracked or warped burner cap can interfere with flame shape and cooking performance. This replacement sits on the burner head, helping distribute the flame evenly while protecting the openings below from spills. Check for food buildup, blocked ports, moisture, and incorrect cap placement before deciding a replacement is needed. Verify fit using the complete appliance model because burner caps may look alike but differ in size or output. Turn every control off and wait until the cooktop is completely cool before installation. Place the clean, dry cap flat over the correct burner. Stop using the appliance if you smell unburned gas.
A cracked or warped burner cap can interfere with flame shape and cooking performance. This replacement sits on the burner head, helping distribute the flame evenly while protecting the openings below from spills. Check for food buildup, blocked ports, moisture, and incorrect cap placement before deciding a replacement is needed. Verify fit using the complete appliance model because burner caps may look alike but differ in size or output. Turn every control off and wait until the cooktop is completely cool before installation. Place the clean, dry cap flat over the correct burner. Stop using the appliance if you smell unburned gas.
This part goes over the top of the oven door glass. The door handle also attaches to the door cap.
This part goes over the top of the oven door glass. The door handle also attaches to the door cap.
Installation Instructions
Barbara from Lagrange, IN
oven door would not stay closed tightly lost of heat
I replaced the door hinges and put a new handle on the oven door. I can not remember what was done exactly because I had a 2 and 4 yr old helping me. But I can tell you that the instructions included with the kit made the job easy. There were a few problems with the type of bit used to get the screws off (I needed a star type of bit, b
... Read more
ut used my phillips because that's what I had on hand). It worked fine, but it would have been better with the star tip screwdriver. There were helpfull hints that told me to prethread the new screws going into the oven door and frame. That was a big help instead of trying to hold the part and start the self threading screws. All in all I would order the parts again and attempt to do another repair on my oven, because it saved me a lot of money. Good luck to all the other first time repairers out there.
Read less
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This genuine OEM oven door vent cap and trim piece is designed to mount along the top edge of the oven door, helping vent heat and steam safely while supporting the door handle and protecting internal components. Made from durable, heat-resistant materials, it maintains proper structure and performance under high temperatures. Ideal for replacing a worn or damaged piece, it helps restore both function and a clean, finished look to your appliance.
This genuine OEM oven door vent cap and trim piece is designed to mount along the top edge of the oven door, helping vent heat and steam safely while supporting the door handle and protecting internal components. Made from durable, heat-resistant materials, it maintains proper structure and performance under high temperatures. Ideal for replacing a worn or damaged piece, it helps restore both function and a clean, finished look to your appliance.
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills.
Installation Instructions
Cathie from WELLS, NY
The range at a round burner and the wife wanted an oblong one
Removed 2 3/16 bolts and burner, set the oblong burner over the orifice and we were all done
This set includes two small and two large burner caps.
This set includes two small and two large burner caps.
Mounting screws are not included.
Mounting screws are not included.
Installation Instructions
James from Federal Way, WA
end caps on range were cracked
I was surprised to find that the 2 screws holding on the plastic end caps were not philips. it looked like an allen wrench deal but that didn't work. Turned out that I had to buy a hex tool. Looked kinda like a swiss army knife but had allen wrench like hex tools in various sizes. By then I was determined to finish the job even if it mean
... Read more
t buying a tool I'd never use again. The job took about five minutes once I had the right tool. The stove looks normal now. The stove looks brand new but for some reason there were cracks in the end caps where the screw hole were.
Read less