Kenmore Range Hinges
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Range Hinges
Your Price
$109.33
In Stock
Kenmore Range Door Hinge
PartSelect Number PS11744215
Manufacturer Part Number WP74008014
The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the left or right hand side of your oven, and is approximately 20 1/2 inches long. If your oven door will not open or close easily, you may need to replace this part. It may be a good idea to replace both hinges at the same time. If a spring has become loose on one hinge, the other hinge is likely to have the same issue. The repair is simple and only requires a Phillips screwdriver and a small bent nail. For a full step-by-step guide, check out the video below.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
William from Statesville, NC
Oven door wouldn't close completely
Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs aren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.
Read more...
Your Price
$7.93
In Stock
Kenmore Range Reciever Hinge
PartSelect Number PS8760079
Manufacturer Part Number W10647259
Fixes these symptoms
- Door won’t close
- See more...
Your Price
$81.03
In Stock
Kenmore Range Hinge- Doo
The hinge replacements did not fix the problem. I think the problem was that the hinge's mating part inside the door had been deformed, perhaps by leaning on the door when fully opened. I compensated for that by placing two stacked magnets near the upper hinge mounting screw hole on the inside of the oven body. (0.75" screws , 8-24 or metric equiv., needed for the upper screw location.) This gave the hinge about 15 degrees of additional door tilting force. In addition, I added 6 ceramic magnets across the top of the door mating surface, kudos to that website. Now it pulls fully flush with the magnets.
Ceramic magnets are good to 400+ degrees and they come in boxes of 120 for $12.00.
I only had one oven as a sample, but I could see what I thought was deformation on the inside of the oven door where the hinges are inserted. In this case, I think that makes (only) hinge replacement futile.
Sorry if this solution does not fit your marketing desire, but I did leave the new hinges installed. Read more...
PartSelect Number PS2088772
Manufacturer Part Number 74011475
Introducing the Whirlpool Oven Door Hinge, an authentic OEM part designed to work with various Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef oven models. This essential accessory is developed to control the rate at which your oven door opens and stays open. It mounts on either the left or right side of the door to ensure easy installation and precise fit. This robust hinge ensures longevity and performance, allowing you to operate your oven with peace of mind. It's recommended to wear work gloves while installing it to guarantee safety. Trust Whirlpool's commitment to quality to provide you with an uncompromised cooking experience.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Barrett from MERCER ISLAND, WA
The oven door didn't shut all the way
Clearly, the oven gasket was not the cause of the problem.The hinge replacements did not fix the problem. I think the problem was that the hinge's mating part inside the door had been deformed, perhaps by leaning on the door when fully opened. I compensated for that by placing two stacked magnets near the upper hinge mounting screw hole on the inside of the oven body. (0.75" screws , 8-24 or metric equiv., needed for the upper screw location.) This gave the hinge about 15 degrees of additional door tilting force. In addition, I added 6 ceramic magnets across the top of the door mating surface, kudos to that website. Now it pulls fully flush with the magnets.
Ceramic magnets are good to 400+ degrees and they come in boxes of 120 for $12.00.
I only had one oven as a sample, but I could see what I thought was deformation on the inside of the oven door where the hinges are inserted. In this case, I think that makes (only) hinge replacement futile.
Sorry if this solution does not fit your marketing desire, but I did leave the new hinges installed. Read more...
Your Price
$44.82
In Stock
Kenmore Range Door Hinge
PartSelect Number PS11754748
Manufacturer Part Number WPW10440013
Upgrade the functionality of your range with this high-quality oven door hinge from Whirlpool. Designed to optimise the operation of your oven door, this hinge controls the rate at which the door opens and keeps it steadily open at an angle when required. Engineered for use with select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef oven models, this hinge ensures a reliable and secure attachment to the left or right side of the door. As a genuine OEM part, it promises excellent durability and performance. Remember to verify that this part is compatible with your specific model before purchase. Please use work gloves for safety when installing.
Fixes these symptoms
- Door won’t close
- See more...
Your Price
$85.42
In Stock
Kenmore Range Door Hinge - Left Or Right Side
PartSelect Number PS2088468
Manufacturer Part Number 74011142
Sold individually.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Patrick from MORAGA, CA
Two digits on the touch pad didn't work "9" & "0". Went to utube and they said hinges go bad causing heat to leak affecting touch pad
Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range.
Read more...
Your Price
$99.78
In Stock
Kenmore Range Door Hinge - Kit Of 2
PartSelect Number PS3504027
Manufacturer Part Number W10347466
This door hinge kit is a genuine replacement part designed to support and guide the oven or range door, ensuring smooth opening, closing, and proper sealing. Typically sold as a set of two or more hinges, it helps prevent issues such as sagging, rubbing, or doors that fail to close correctly. Over time, hinges can wear out or become misaligned, affecting performance and heat retention. Replacing them restores the appliance’s functionality and efficiency. Installation involves removing the old hinges and securing the new ones for a precise fit.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Ross A from Sugar City, ID
Oven door would not close completely
Open door 1/4 an slide the little latches on each hinge toward you. This will lock them in place. Close the door a little and lift it up. The door will slide out. Lay it face down on a table and undo all the screws. Do not remove the glass, frame etc. Slide old hinge out and new one in being careful not to slide the glass and frame out of alignment. It is a pain to get it all back together if you take every part out. Just do the hinges. Screw it back together. Reverse the door removal process by lowering the hinges into the oven receiver from a 75% closed position. Once in place, open the oven about halfway and slide the locks forward. This will allow the door to close completely. Note: Three hinges came with my set. Not sure what the third odd one is for.
Read more...
Your Price
$61.52
In Stock
Kenmore Range Door Hinge - Left Side
remove door;
remove old hardware;
since hinge openings were bent, straighten hinge opening in oven face;
attach spring to inside of oven;
slide hinge through opening;
attach spring to hinge;
screw hinges to oven face;
repeat on other side;
attach hinges to door;
while decorative panels are off, vacuum
install decorative panels.
DONE. Read more...
PartSelect Number PS1151518
Manufacturer Part Number 318348801
This hinge is located on left side of the oven door.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Xavier from Rocky Point, NY
Springs pooped off door hinges, causing hinges to break through door face
Remove decorative side panels on stove to expose backside of hinge and springs;remove door;
remove old hardware;
since hinge openings were bent, straighten hinge opening in oven face;
attach spring to inside of oven;
slide hinge through opening;
attach spring to hinge;
screw hinges to oven face;
repeat on other side;
attach hinges to door;
while decorative panels are off, vacuum
install decorative panels.
DONE. Read more...
Your Price
$39.84
In Stock
Your Price
$130.54
In Stock
Kenmore Range Hinge Kit
PartSelect Number PS979954
Manufacturer Part Number 5304445529
This kit comes with 2 door hinges, 2 brackets and 4 screws.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Barbara from Lagrange, IN
oven door would not stay closed tightly lost of heat
I replaced the door hinges and put a new handle on the oven door. I can not remember what was done exactly because I had a 2 and 4 yr old helping me. But I can tell you that the instructions included with the kit made the job easy. There were a few problems with the type of bit used to get the screws off (I needed a star type of bit, but used my phillips because that's what I had on hand). It worked fine, but it would have been better with the star tip screwdriver. There were helpfull hints that told me to prethread the new screws going into the oven door and frame. That was a big help instead of trying to hold the part and start the self threading screws. All in all I would order the parts again and attempt to do another repair on my oven, because it saved me a lot of money. Good luck to all the other first time repairers out there.
Read more...
Your Price
$10.92
In Stock
Kenmore Range Hinge
PartSelect Number PS11740954
Manufacturer Part Number WP3195060
Sold individually.
Related Kenmore Range Parts
- All Kenmore Range parts
- Kenmore Range Bearings
- Kenmore Range Brackets and Flanges
- Kenmore Range Caps and Lids
- Kenmore Range Circuit Boards and Touch Pads
- Kenmore Range Cooktops
- Kenmore Range Deflectors and Chutes
- Kenmore Range Doors
- Kenmore Range Drawers and Glides
- Kenmore Range Drip Bowls
- Kenmore Range Ducts and Vents
- Kenmore Range Electronics
- Kenmore Range Elements and Burners
- Kenmore Range Fans and Blowers
- Kenmore Range Filters
- Kenmore Range Fuses
- Kenmore Range Grates
- Kenmore Range Handles
- Kenmore Range Hardware
- Kenmore Range Hoses and Tubes
- Kenmore Range Igniters
- Kenmore Range Ignitions
- Kenmore Range Insulations
- Kenmore Range Knobs
- Kenmore Range Latches
- Kenmore Range Legs and Feet
- Kenmore Range Lights and Bulbs
- Kenmore Range Manuals and Literatures
- Kenmore Range Motors
- Kenmore Range Panels
- Kenmore Range Power Cords
- Kenmore Range Racks
- Kenmore Range Seals and Gaskets
- Kenmore Range Sensors
- Kenmore Range Springs and Shock Absorbers
- Kenmore Range Switches
- Kenmore Range Thermostats
- Kenmore Range Timers
- Kenmore Range Touch-Up Paint
- Kenmore Range Transformers
- Kenmore Range Trims
- Kenmore Range Valves
- Kenmore Range Wheels and Rollers
- Kenmore Range Wire Plugs and Connectors