Kenmore Range Valves

Kenmore Appliance Parts
Shop By Part Type

Popular Kenmore Range Valves

Your Price
$34.37
  In Stock
Natural Gas to Liquid Propane Conversion Kit
★★★★★
★★★★★
(7)
PartSelect Number PS2351422
Manufacturer Part Number GRLP3
This kit is used to convert your appliance to liquid propane.
Installation Instructions
Denny from Bishop, CA
Bought a new gas oven that did not come with a propane conversion kit.
I followed the simple instructions that were included in the kit. I started by replacing the 5 orifices on the top burners. The orifices are well labeled with numbers and colors. Next, I tightened the broiler burner orifice and the oven burner orifice with a 1/2 inch wrench. I had to tighten them pretty good to get the flame down where it is supposed to be. Then, I checked for leaks and I was then ready to cook. Read more...
Your Price
$68.25
  In Stock
Double Burner Assembly
★★★★★
★★★★★
(6)
PartSelect Number PS232404
Manufacturer Part Number WB16K10026
Both burners are mounted on the same bracket.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Will Not Start
  • See more...
Installation Instructions
Helen from Flemington, NJ
My old burners were beyond the point of coming clean and made my stove top look bad.
My husband and I simply took the burner units out of the packing, took the old ones off, put the new ones in. The new units needed to be leveled, but the leveling nuts included fit perfectly, and the entire repair took less than 15 minutes. Read more...
Your Price
$29.81
  In Stock
Burner Head - Medium - 9500
★★★★★
★★★★★
(9)
PartSelect Number PS1020327
Manufacturer Part Number WB16K10055
This burner head, or surface burner, is used in ranges and ovens. The burner sends gas through the holes and slots to create an equal flame across the cooking area. If the gas igniter glows but will not light up, or there are heating inconsistencies, replacing the burner head could be the solution to your problem. No tools are required for this installation. To change the burner, first lift the grate and take the burner cap off. Next, lift the burner away from the cooktop. To set the new burner in place correctly, check the locating tab that fits into the V-shaped notch and make sure the igniter fits into the cut-out. Refer to the diagram provided by the manufacturer for further instructions.
Fixes these symptoms
  • Gas igniter glows, but will not light
  • Will Not Start
  • See more...
Installation Instructions
Alejandro from Newark, NJ
The Burners and Burner Caps were missing
Very simple repair. I bought the Range without the Burners and Burner Caps. So all I had to do was to purchase the Burners and the Burner Caps and drop them in. Wish everything in life would be that simple. Read more...
Your Price
$16.03
  In Stock
Left Front Orifice - 9.5K
★★★★★
★★★★★
(2)
PartSelect Number PS2332664
Manufacturer Part Number 316527500
Your Price
$27.15
  In Stock
Small Burner - 5K
★★★★★
★★★★★
(8)
PartSelect Number PS3486550
Manufacturer Part Number WB16K10070
Sold individually.
Fixes these symptoms
Installation Instructions
Alejandro from Newark, NJ
The Burners and Burner Caps were missing
Very simple repair. I bought the Range without the Burners and Burner Caps. So all I had to do was to purchase the Burners and the Burner Caps and drop them in. Wish everything in life would be that simple. Read more...
Your Price
$16.94
  In Stock
Right Rear Orifice
★★★★★
★★★★★
(1)
PartSelect Number PS2349573
Manufacturer Part Number 316527504
Your Price
$60.45
  In Stock
Front Burner
★★★★★
★★★★★
(4)
PartSelect Number PS11770472
Manufacturer Part Number 5304506427
This is a front burner assembly for the stovetop on your range. It delivers the gas to the main cooking area by dividing it through the slots or holes in order to create an evenly burning flame. Take note that this is a front burner assembly. If you are looking to replace your rear burner assembly, see that in the related parts section. This model is roughly 8 inches long, 4 inches wide, and 4 inches thick.
Installation Instructions
PATRICIA from OPA-LOCKA, FL
One of the two front burners was broken and the second was leaking gas.
Unplug the old ones and the new ones snapped into place. Read more...
Your Price
$59.34
  In Stock
Back Burner
★★★★★
★★★★★
(1)
PartSelect Number PS11770471
Manufacturer Part Number 5304506426
Installation Instructions
LETICIA from South El Monte, CA
Back & front burners where broken and did not stay in place, Unable to use in regular cooking.
I looked in PARTS SELECT.COM immense inventory of replacements parts, found the right ones, order them, got in with in two days, replaced the old ones with the new parts, Now we are cooking!! Thank you. Read more...
Your Price
$21.71
  In Stock
Left Front Orifice
★★★★★
★★★★★
(6)
PartSelect Number PS954084
Manufacturer Part Number WB28K10190
This is the replacement left front orifice for your gas range. When your range is operating, gas flows through the orifice to the igniter. This part is the orifice itself as well as the metal holder that holds it in place. If you notice a gas smell when your range is on, you could have a loose or damaged orifice. This part fits the front left burner in your range, so make sure you are replacing the correct orifice. This is an OEM part sourced from the manufacturer and is sold individually.
Fixes these symptoms
Installation Instructions
Kimberly from Leavittsburg, OH
loss of spark to two burners, and bent orifice holder
unplugged the old spark module and plugged the new one in. Disassebled and reassembled the new orifice holder. Read more...
Your Price
$56.28
  In Stock
Front Burner Igniter/Orifice Assembly
★★★★★
★★★★★
(3)
PartSelect Number PS2332312
Manufacturer Part Number 316237805
This igniter and orifice assembly is a legitimate OEM replacement part for your gas stove, and includes the igniter, orifice assembly, and gas tube. This part may need replacing if the igniter fails or the tube is leaking gas. It is a very easy repair. Remove the grates and burners from the range. Unscrew the existing assemblies and pry off the cooktop. Locate the assembly you are replacing and undo the nut holding it in place. Pull out the igniter wire by hand, and install the new one, replacing the rest of the parts in reverse order.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Will Not Start
  • See more...
Installation Instructions
Steve from NORTH PEKIN, IL
the new burners had no threads for the screws
had to use a tap and cut new threads. Also had to remove the top of the range, and the metal cover under the top. Read more...

Related Parts