Kenmore Range Trim
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Range Trim
Your Price
$16.95
In Stock
Kenmore Range Bottom Trim Channel (white)
PartSelect Number PS16742549
Manufacturer Part Number WB07X42948
This part is the replacement door trim for your oven. It is white in color and is approximately 30 inches long and 2 inches wide. The bottom door trim supports the outer glass from the bottom. The main reason to replace the bottom door trim is if it is cracked or damaged, or if it is corroded and you cannot close your oven door properly. This part is sold individually and is an authentic OEM part.
Installation Instructions
Donald from Delmar, NY
Range door bottom trim got rusty: a lousy design by GE.
I used a screwdriver and pliers. A nut driver would have been helpful. Oven door is removeable for cleaning and maintenance, but it's heavy and awkward. It has to be laid face-side down to disassemble, so have a protected tabletop ready to avoid scratches. Side trim pieces have to come off to get access to bottom trim mounting screws.
Read more...
Your Price
$41.95
In Stock
Kenmore Range Door Trim Right Side (black)
PartSelect Number PS10066094
Manufacturer Part Number W10761014
NOTE: The trim has been re-designed and no longer requires the screws. The dimples on the bottom hold them in place instead.
Installation Instructions
William from HADLEY, PA
Broken Trim Pieces
Remove vent trim from oven and set oven glass to the side. Next remove handle from vent trim (two screws). Next place handle on new vent trim. Place glass in place, (it is held in place by bottom of oven door and vent trim). next place side trim in place and place that side of the vent trim and loosely tighten screw holding trim into place at top of the glass. Next place the other trim into place under the vent trim and tighten the screws on both sides.
Read more...
Your Price
$53.30
In Stock
Kenmore Range Side Trim Right Hand
PartSelect Number PS11746045
Manufacturer Part Number WP8523166
This trim is white in color.
Installation Instructions
Philip from Vandalia, MI
Replace shattered outer door glass
This is not the best design. You'll need to have an extra set of hands to hold the trim pieces in place. Remember the glass is positioned outside [on top of]the trim pieces. Be careful as the trim pieces are rather brittle and can be hard to locate in their proper position. Position glass in the holding tabs at the bottom, hold glass against the trim pieces and gently position door handle over glass and trim.The handle holds everything together. No instructions are shipped w/ parts.
Read more...
Your Price
$53.30
In Stock
Kenmore Range Side Trim
PartSelect Number PS11746047
Manufacturer Part Number WP8523172
Screws are not included with the trim. Must order screws separately.
Installation Instructions
Philip from Vandalia, MI
Replace shattered outer door glass
This is not the best design. You'll need to have an extra set of hands to hold the trim pieces in place. Remember the glass is positioned outside [on top of]the trim pieces. Be careful as the trim pieces are rather brittle and can be hard to locate in their proper position. Position glass in the holding tabs at the bottom, hold glass against the trim pieces and gently position door handle over glass and trim.The handle holds everything together. No instructions are shipped w/ parts.
Read more...
Your Price
$64.63
In Stock
Kenmore Range Door Trim Kit
2. Remove 2 top screws holding vent cover and carefully remove
cover
3. Open door all the way and lift, door will come of the microwave
4. Set door on a flat surface facing down
5. You will need a flat screwdriver,carefully set the screwdriver
between the door and the black plastic and pry out completely
6. Remove screws holding handle. (This will be a good time to clean
the inside of this door)
7. Attach new handle tighten screws
8. Put black plastic back in door and press on all around make sure
that is set in place
9. Re-install door and vent. Read more...
PartSelect Number PS2364260
Manufacturer Part Number 5303935318
Introducing the Frigidaire Door Trim Kit, a genuine OEM part designed to frame the sides and bottom of your oven door for a sleek and polished look. Crafted with precision, it ensures a perfect fit for select models of Frigidaire, Electrolux, White Westinghouse, and Tappan stoves, ovens, and ranges. Its 3-sided, white design adds an elegant touch to your appliance, matching a variety of kitchen aesthetics effortlessly. This kit may come with multiple parts, so we recommend you refer to your parts diagram for a complete list. Before you begin, ensure your oven door has cooled down. Quality and durability are guaranteed with the Frigidaire range door trim kit. Please verify the compatibility with your model before placing an order to avoid any discrepancies.
Installation Instructions
Robert from WATERTOWN, MA
Broken Handle
1. Order part2. Remove 2 top screws holding vent cover and carefully remove
cover
3. Open door all the way and lift, door will come of the microwave
4. Set door on a flat surface facing down
5. You will need a flat screwdriver,carefully set the screwdriver
between the door and the black plastic and pry out completely
6. Remove screws holding handle. (This will be a good time to clean
the inside of this door)
7. Attach new handle tighten screws
8. Put black plastic back in door and press on all around make sure
that is set in place
9. Re-install door and vent. Read more...
Your Price
$27.95
In Stock
Kenmore Range Bottom Trim (white)
PartSelect Number PS2321159
Manufacturer Part Number WB07K10250
Screws not included.
Installation Instructions
Katheryn from BEACON FALLS, CT
RUSTED TRIM PEICE
REMOVED THE DOOR, TOOK THE SCREWS OUT OF THE BOTTOM AND REPLACED THE TRIM. IT TOOK CARE TO GET THE TRIM OVER THE GLASS ON THE DOOR. IT WENT RIGHT ON AND LOOKS LIKE NEW.
Read more...
Your Price
$41.95
In Stock
Kenmore Range Door Trim Left Side (black)
PartSelect Number PS10066095
Manufacturer Part Number W10761018
NOTE: The trim has been re-designed and no longer requires the screws. The dimples on the bottom hold them in place instead.
Installation Instructions
William from HADLEY, PA
Broken Trim Pieces
Remove vent trim from oven and set oven glass to the side. Next remove handle from vent trim (two screws). Next place handle on new vent trim. Place glass in place, (it is held in place by bottom of oven door and vent trim). next place side trim in place and place that side of the vent trim and loosely tighten screw holding trim into place at top of the glass. Next place the other trim into place under the vent trim and tighten the screws on both sides.
Read more...
Your Price
$47.95
In Stock
Kenmore Range Door Trim Kit
PartSelect Number PS10064749
Manufacturer Part Number 5303935377
Introducing the Door Trim Kit, a genuine OEM part specifically designed for a perfect fit with select Frigidaire oven/range models. This modern 3-sided kit enhances the aesthetic appeal of your kitchen while also remaining functional, effortlessly framing the sides and bottom of the oven door. Should you decide to install this part, please allow your oven door to cool completely before starting for safety. This black Door Trim Kit not only affirms quality but also durability, ensuring long-lasting performance for your cooking needs. It's highly recommended to thoroughly examine the compatibility of your model prior to placing your order, as this part can have minor variations in size and shape. Perfect your oven with the sleek and sturdy Frigidaire Door Trim Kit.
Your Price
$57.77
In Stock
Kenmore Range Trim Lower (white)
PartSelect Number PS11746049
Manufacturer Part Number WP8523175
Trim only in white. Screws not included.
Installation Instructions
Jeffrey from Orange, CA
Your Price
$52.87
In Stock
Kenmore Range Door Trim
PartSelect Number PS11746048
Manufacturer Part Number WP8523173
Installation Instructions
John from Madison, WI
Followup Repair to Install Door Trim
I had to unscrew the handle from the door as well as take out the front glass, put the trim in place (Thank God for the bottom placement nipples on each trimpiece), hold everything together after aligning all the pieces in place while I screwed the handle back on. The reason I was replacing the trim in the first place was that it is fragile plastic that had broken on both sides when I replaced one inner glass piece that had broken.
Read more...
Related Kenmore Range Parts
- All Kenmore Range parts
- Kenmore Range Brackets and Flanges
- Kenmore Range Caps and Lids
- Kenmore Range Circuit Boards and Touch Pads
- Kenmore Range Cooktops
- Kenmore Range Deflectors and Chutes
- Kenmore Range Doors
- Kenmore Range Drawers and Glides
- Kenmore Range Drip Bowls
- Kenmore Range Ducts and Vents
- Kenmore Range Elements and Burners
- Kenmore Range Filters
- Kenmore Range Grates
- Kenmore Range Handles
- Kenmore Range Hardware
- Kenmore Range Hinges
- Kenmore Range Hoses and Tubes
- Kenmore Range Igniters
- Kenmore Range Ignitions
- Kenmore Range Insulations
- Kenmore Range Insulations
- Kenmore Range Knobs
- Kenmore Range Latches
- Kenmore Range Legs and Feet
- Kenmore Range Lights and Bulbs
- Kenmore Range Motors
- Kenmore Range Panels
- Kenmore Range Racks
- Kenmore Range Seals and Gaskets
- Kenmore Range Sensors
- Kenmore Range Springs and Shock Absorbers
- Kenmore Range Switches
- Kenmore Range Thermostats
- Kenmore Range Valves
- Kenmore Range Wire Plugs and Connectors