MFI2569VEM10 Maytag Refrigerator - Instructions

It took one minute to put the shelf in. The best part was the speed with which the part arrived. I also want to compliment the operator I dealt with. She was very helpful.

Removed crisper drawers and the crisper frame. Then removed the glass shelf from the frame and also the plastic front piece and the metal rod that adds stability to the frame. Those last two items required a screw driver and pliers. Inserted the metal bar into the new frame, popped on the front piece, and installed frame in frig. Put in center rail, then glass top, and then put in crisper drawers.

The repair was straight-forward once the pantry drawer and lower shelves were emptied and removed - remove the mounting screws, replace the broken end cap with the new part. It took me several minutes to reattach everything. It took me longer to clean up all the old food spills under the pantry drawer.

Removed the old bar. Replaced the part that moved the shutter open and closed. Installed the new parts. Put the drawer lid back in place. Working fine. Thanks!!

I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.

I used the feedback information from others who commented on your website

replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

Similar to other reports. Only thing I can add is the nut driver is 1/4" and it is all I needed to remove and replace all five screws.

Removing the large drawer,2 drawers,glass shelve & 2 end supports,two screws on the sliding track & two screws on the Pantry end cap it took me 15 minutes. When removing the left Pantry end cap on the right side, care must be taken because Center Crisper Rail #PS 162879 is attached to the Pantry End cap at the back & real care must be taken to remove it. After all the screws are removed pull the end cap carefuly towards you while moving all to the left until it clears the back wall of the refrigerator. Again, real care must be taken using a flat head screwdriver to remove the plastic track for the Center Crisper Rail. The Pantry End Cap on the left is a lot easier to remove than the right side.

Simply remove the filter and insert the bypass cap in its place. Cap turned a little hard but if your careful everything goes together easily.

The large pull out full width drawer cover hinge pin broke off on the left side. The repair is easy with just two tools, a 1/4" nut driver and a phillips head screw driver. I removed the two conventional drawers that sit above the wide drawer with the broken hinge. Next lift out the glass divider that sits on top of the wide drawer and set it aside and remove the two braces front and back by lifting them out of their respective grooves. Remove the wide drawer with the lid by pushing in on the two black clips on each side of the drawer slide up towards the front and pull entire drawer out while putting pressure on the two clips at the same time. The drawer should come out leaving the drawer slides behind. Unscrew the 1/4" hex screws on the broken side panel using the nut driver and gently pull the side panel straight back toward you. Remove the drawer slide from the broken piece by unscrewing the two phillips head screws and rescrew the drawer slide onto the new side panel. Replace everything in reverse order. One note: do not use too much torque on the screws when replacing the parts as they only screw into plastic, this will avoid them stripping out. A snug fit is all you're after. There now, go pop a beer and sit down and relax, you are now a refrigerator repair man!

Remove two upper trays. glass shelf and shelf brackets. Remove bottom tray. unscrew side with back vent openings and remove with humidifier controls attached. Carefully remove control arms and back vent cover. Install on new unit and screw back in place. Check to make sure hinge pin lifts drawer top properly.

This was a very simple repair. It took longer to remove the crisper bins than it did to repair the pantry end cap.

A few screws out and in. and the rail just clipped in under the glass

used the directions from PartSelect