Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MFI2569VEM10 > Instructions

MFI2569VEM10 Maytag Refrigerator - Instructions

All installation instructions for MFI2569VEM10 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MFI2569VEM10
496-510 of 714
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Pantry Drawer Lid was Broken on the left side

  • Customer: Bish from Bronx, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took out the old part(2 screws) and installed the new one and it was fixed, very easy and rewarding, for $20 this was great, a service repair company wanted $150 just to assess the problem.

Meat Drawer Cover Hinge Broke

  • Customer: Robert from Kingsport, TN
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The nipple on the "pantry end cap - left side" that acted as part of the hinge for the meat drawer cover broke off. After receiving the replacement pantry end cap, I removed the meat drawer, removed the 2 vegetable bins, removed the glass shelf above the meat drawer, removed the screws holding the old pantry end cap, and pulled the old cap out. Then I put the new cap in place, screwed it in, and replaced everything else. The most surprising part of all of this is that I ordered my part on 4/22 and received and installed it on 4/25; 3 days! Thank you partselect for your fast response.

Cleaning glass and shattered into a million pieces

  • Customer: Eric D from Sheridan, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Found glass here and ordered. Had it 2 days later and set new glass in and back in business.

center rail which supports 2 crisper drawersThe rail needs to be lined up with the drawers

  • Customer: Mary from Riverside, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The rail & the drawers need to be aligned with each other & then push the rail into the little hole in the back wall of the frig while sliding the drawers in at the same time. I think I put too much fruit & vegs in the drawers which makes them heavy & the little tab which is there to support the drawers has broken off twice. This is the 2nd time I have ordered this rail. It would be helpful if the rail had a vertical supporting post towards the front. I like to have a lot of produce on hand all the time

Cover to bottom bin would not stay secured. broken plastic support pin

  • Customer: RAY from HOUSTON, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed Left side support with broken pin (3 small hex head bolts). Replaced with new support with pin in place. Note behind: I broke the pin trying to replace the cover. Now I know to flex back the side to the cover, and not flex the pin which broke. This cost me 25 bucks and one hour, saving me from a probable $300 dollar charge. THANKS, PARTS SELECT!!!!!

The very small piece that holds the cover on to the drawer broke off.

  • Customer: Pamela from Ellabell, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed long drawer. Unscrewed the end cap. Removed slider from broken end cap. Reconnected the slider to the new end cap. Screwed new end cap in place. Replaced drawer. Done!

Broken tab that hold the lid for the drawer

  • Customer: Mike from Conway, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove all three drawers. Remove the glass panel. Remove screws from pantry end cap. Remove end cap from refrigerator. Remove temperature control assembly from old end cap. Install temperature control on new end cap. Install new end cap in refridgerator. install screws. Put glass panel back in refrigerator. Put drawers back in refrigerator. Install drawer lid on new end cap. Close the refrigerator. The part arrived within two days. The repair took a total of 20 minutes from opening the box with the new part to closing the refrigerator door after the job was complete.

Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.

  • Customer: Burton from Pecatonica, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

End cap on left side of refrig Deli drawer on Kitchen Aid broke. Ordered and replaced part, no problems.

  • Customer: James E from Laguna Niguel, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took shelves and crisper drawers out, took broken left panel out with nut driver and then replaced with new part. Installed drawers and glass shelf and finished.

broken center rail

  • Customer: Tom from Jamison, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This rail holds up the two crisper drawers.It was easy to select and order it on your website. It arrived in a few days with standard shipping instruction, and snapped in place in a few seconds.

I broke the switch pulling the freezer basket out.

  • Customer: George from Palatine, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.

you have to turn it off and on to run.

  • Customer: chris from woodland hills, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

Pantry end cap right side.

  • Customer: Frank from Palm Coast, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removing the large drawer,2 drawers,glass shelve & 2 end supports,two screws on the sliding track & two screws on the Pantry end cap it took me 15 minutes. When removing the left Pantry end cap on the right side, care must be taken because Center Crisper Rail #PS 162879 is attached to the Pantry End cap at the back & real care must be taken to remove it. After all the screws are removed pull the end cap carefuly towards you while moving all to the left until it clears the back wall of the refrigerator. Again, real care must be taken using a flat head screwdriver to remove the plastic track for the Center Crisper Rail. The Pantry End Cap on the left is a lot easier to remove than the right side.

Filter was blocked and I wanted to Bypass

  • Customer: ARTHUR from FT. MYERS, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply remove the filter and insert the bypass cap in its place. Cap turned a little hard but if your careful everything goes together easily.

Drawer lid hinge broken

  • Customer: Randy from Escondido, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The large pull out full width drawer cover hinge pin broke off on the left side. The repair is easy with just two tools, a 1/4" nut driver and a phillips head screw driver. I removed the two conventional drawers that sit above the wide drawer with the broken hinge. Next lift out the glass divider that sits on top of the wide drawer and set it aside and remove the two braces front and back by lifting them out of their respective grooves. Remove the wide drawer with the lid by pushing in on the two black clips on each side of the drawer slide up towards the front and pull entire drawer out while putting pressure on the two clips at the same time. The drawer should come out leaving the drawer slides behind. Unscrew the 1/4" hex screws on the broken side panel using the nut driver and gently pull the side panel straight back toward you. Remove the drawer slide from the broken piece by unscrewing the two phillips head screws and rescrew the drawer slide onto the new side panel. Replace everything in reverse order. One note: do not use too much torque on the screws when replacing the parts as they only screw into plastic, this will avoid them stripping out. A snug fit is all you're after. There now, go pop a beer and sit down and relax, you are now a refrigerator repair man!
All Instructions for the MFI2569VEM10
496-510 of 714