MFI2569VEM10 Maytag Refrigerator - Instructions

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

Easy site to locate your part. Arrived at my house quick and installed very easy. If I ever need another appliance part I will be coming back to partselect.com!

simple fix, remove and replace anyone with basic tool skills could do this. what prompted me to post here was the great service at parts select. website is very easy to use and their customers service reps are courteous and helpful. will use these guys anytime and highly recommend them. and did i mention the speedy delivery, had my parts in a couple of days. in the past i have waited for weeks from other parts houses.

I removed all shelving. Used a cordless screwdriver with nut piece on end and took out nuts. Then had to CAREFULLY remove the mechanism that lets in cold air by gradation from the old end cap. Then put these parts on the new end cap. This took some thinking. Finally reset endcap and put unit back together again. Sucess and I am 61 and female.

My ice maker would not produce ice. I removed motor module which involved removing ice maker from freezer, removing motor module cover and 3 screws. I found short (burnt place) in copper of existing module. Ordered new motor module, replaced, and all is fine. Great service, quick delivery and correct part.

We removed the old one nd made note of how it fit into the back. We screwed it into place and put the door back on. No problems at all

I pulled out the pantry drawer, the two crisper drawers above, and the glass shelf and supports.
I used a 1/2" nutdriver to take out 3 nuts and then reused them to put in the new pieces. Save your existing hardware since new nuts were not supplied. This was so easy! The right one was a little more challenging because of the temperature control. Take a minute to see how it works when you take it off the old one. That will help you recreate it on the new one.
I am a fairly handy woman. I did ask one of my guy friends to help me find the right tool to use.
This was really easy. I think the original design is cheap and poorly done, especially considering how much we paid for this fridge.

I removed the drawers, glass shelf and the old frame. I had to remove several parts from the old frame and reinstall on the new one. It took a couple of minutes to figure out how to remove one part by prying with a small screwdriver. Otherwise, everything was straightforward.

The leftover broken piece of the rail was removed from the crisper shelf supporting brackets and the new replacement installed in place using the front and rear tabs inserted into the crisper support bracket. Both crisper drawers now slide in and out properly.

First all product had to be removed in order to remove glass top that cover the crisper drawers, then removed both drawers and thenremoved the broken Crisper Frame Center Rail and installed the new part. Even with cleaning everything and putting it back together the whole job was only about twenty minutes of work time. Best thing of all was the price for the part, I will try to use PartSelect item for any other repairs I do on my appliancce!!

It took longer to take the items[food] out than to repair. It was very easy to replace.

Used the instructions on your site.

frist i loosend the two hex screws then took of handle then put handle back on and tighten up hex screws

Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.