Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Crisper Drawer / Cracked Pantry Lid
Thanks to others who shared their story, I was prepared to "muscle" the front cover off the old crisper and snap it into place on the new crisper -- warning if you are good with puzzles and mechanics, this repair is a "snap"; Pantry Lid is very easy, push pin on left side, slide old lid out and push new lid in.
pulling the dairy draw out, a plastic knob broke,that keeps the cover on the draw on tight.
after pulling the draw out. had to remove 3 screws on the left side, pull out one part, and then replaced the broken pin. put everything back in place and it was done.perfect job.saved alot of money. thanks to part-select
Ice door cycling automaticly,huge block of ice in freezer.
Started with removing freezer door assembly, with the freezer compartment empty next to remove was the rear panel exposing the thermostat and evap coils. With frige away from wall, I removed panel covering the circut board. Used the hairdryer to remove ice from coils and surrounding area. Did a continunity check on wires from thermostat to the circut board, door connections to the board, ohm test on thermostat. The goofy things that frige was doing( blinking lights, ice door cycling on it's own, 3'' slab of ice sitting at the bottom) I called the board bad. Bad board!! Use a small standard screw driver to gently force retaining tabs (2 each) back to remove the circut board, be gentle the tabs are plastic, slide the board out. For the install it is really going in a reverse order. Slide the in and gently snap the circut board in the tads, make your connections, reinstall panel, freezer interior panel, and freezer door assembly. Good straight forward stuff. The programming steps are also straight forward, I did this step 4 times before it got it right.. Hope this helps.
This was actually very easy, take the two crispers out and the glass panel over the large drawer and the two holding brackets that hold the glass above.
then just use a nutdriver to remove the three nuts, gently pull the piece out and remove the slider with a screwdriver (two screws). Attach the slider to the new piece reinstall, it's very easy. Took 15 minutes tops.
This was for the left side the right side might be more problematic with the additional humidity controls I don't know ....
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
First I removed the pantry shelf and all the shelving on the bottom half of the fridge. I used the nut driver to remove the RH pantry end cap. Very easy. I took a picture with my digital camera to make sure that I remembered how the assembly looked when puttin git back together. Very easy to do. Common sense repair.
I'd been looking a broken plastic for 3 years. Googled Partselect on a whim and one week later a new drawer and lid arrived at my door. 10 minutes later the refridgerator was like new again.
had to remove shelving, crisper's, then unscrewed end cap. lifted it off set pin. and reversed for reinstallation. reefer door is reversed which makes it prone to close on crisper if not fully closed
With 2 babies and a chaotic household, i failed to double-check the measurements before I ordered the part. No fault of partselect, just user error ;-) I had to return the part bc i ordered the wrong size. Lesson learned, take my time and make sure it's done right the first time. The part fit in perfectly. I used the search feature on the left side of the website to find the part, since the deli drawer wasn't in the parts diagrams given. The second time, customer service helped me find the part since the correct part wasn't on the website initially. The deli drawer for this model is in the perfect place to have something dropped on it time and time again. I'm surprised you don't get more requests for this part to be replaced. It's bad design for Maytag to make it out of thin plastic. Anyway, thanks so much for your patience in dealing with this frenzied mom! :-)
It was great! Took my husband less then 5 minutes to fix. Your delivery time is excellent. This is the second time I order from you and would do so again if the need arises. Thank you so much. Don't be afraid people go ahead and order.
I have to say this was the smoothest repair ever! It was easy to find on the site, ordering was easy, part came, snapped off, snapped on new drawer, FINISHED! Thank you!
The high voltage circuit panel in the back of the unit was bad. I was going to first replace the low voltage board behind the water/ice dispenser, but a post clued me that the real problem was the high voltage board. The part came the next day and took only a few minutes to install. The board must be programmed once installed. Follow the included instructions carefully and exactly. Fixed the problem completely.