LSE7806ACE Maytag Washer Dryer Combo - Instructions

After making sure the lines and screens are clean, and there is good water flow thru the hoses to the valves, and there is power to the valve solenoids, (which can be detected by setting to fill and pulling out on the start knob), and hearing a "click" at the valve, you can summize that the valve is weak, or partially blocked internally.
Replace the valve by unpluging the power cord to the machine. Remove the hoses. Remove the screw that attaches the valve mounting plate. Pull the plate and valve out and remove the screw that attaches the valve to the plate. Unplug the wires from the solenoides,[IMPORTANT] noting which wires go to each valve. Remove the rubber hose on top of the valve by squeezing the hose clamp with a pair of pliers, and sliding the clamp up the hose. Now you can pull the hose off. Install the new valve in the reverse order.

Made a 4 prong wrench from a 2" pipe coupling to remove retaining nut. Had to tap retaining washer a few times with hammer and after that it came off very easy. All other work was very easy. parts went together with ease. Saved company several $'s as we were told it was not recomended to repair and should replace washer. Under $100 for parts and a couple hours labor.

1 Disconnect dryer from electrical outlet
2 remove vent pipe
3 Tilt dryer backwards and remove front cover bottom 2 philips screws.
4 remove lint assembly and then the fan blower housing with nut driver.
5 with pliers remove retainer clip from fan
6 remove snap ring with pliers or a flat blade screw driver will also work.
7 remove fan
at the same time I replaced the front glides if you do not want to do this then reinstall in reverse order and job is complete.

for glide replacement
1 remove the 4 screws holding the outer ring to the frame of the dryer.
2 drill out old rivits from the back side and then knock out. be careful to only drill rivit and not into metal frame
3 install new new glides makesure you install in correct direction.
4 install pop rivets with stud end on top side of glide. pushing rivet through glide and into the frame ring.
5 pop rivits and make sure they are secure.
6 reinstall ring making sure seal is around ring correctly
7 reintal 4 screws.
8 follow reassembly of blower and lint housing if you changed the fan. if not then just the lint assembly.

good luck the job is really easy and you will save yourself some money

The repair itself was pretty easy. Though I had figured out what needed to be done on my own while I waited for the belt to arrive via Fed Ex, the belt arrived with instructions that described the plan I had already figured and if I hadn't known what I was doing, the instructions would have been a great help.

STEP ONE, UNPLUG THE UNIT (and/or shut off the gas supply), CAREFULLY. Then, I took the front of the unit off by removing the 2 screws on the front panel near the bottom of the unit and disconnected the wiring that shuts the unit off when the door is opened. Set the front door panel aside. Then I removed the front of the tumbler retainer along with the exhaust duct and lint screen assembly by removing 4 screws that affixed the reatiner frame to the rest of the outer cabinet. Set this aside as well. Remove the entire tumbler unit. Set aside. Remove 4 screws on the back of the unit that hold the tensioner and motor access panel and remove it. Set it aside. At this point, I vacuumed every bit of lint and debris from the snapped belt out of the enitre unit, lubricated/greased all moving parts, cleaned off the friction bearing surfaces, and collected loose change ($1.35).

When the belt arrived, I unwrapped it, and placed the smooth side to the tumbler and rubber banded the slack off to the bottom right side (sort of the 4:30 position as you put the tumbler back into the unit). I carefully jimmied the tumbler back into the unit BEING CAREFUL not to pinch the groved belt between the tumbler and any other parts inside the cabinet. I replaced the tumbler retainer and screwed the 4 bolts back into place. I spun the tumbler over near the tensioner assembly (so I could see the slack through the access panel hole in the back) and removed the rubber band. I threaded the belt through the tensioner and over the drive pulley and rotated the tumbler clockwise to align the drive train of the belt. I plugged the 2 wires back into the switch on the inside of the door panel and then I replaced it on the front of the unit and screwed the 2 screws back in at the bottom front of the panel. I plugged the unit back in and tested opperation. It worked great! I unplugged the unit again (I'm not finished yet). I then replaced the access panel on the back of the unit and screwed the 4 screws back in. I moved the unit back against the wall and plugged it back in. Done! The dryer is less noisey now and more efficient most likely b/c I cleaned all the lint out of the thing! Thanks for the prompt shipment of the belt!! I'll get a few more years out of this dryer before spending $700 on a new one!!! Thanks again!

The job went fast an well

The motor was easy to replace: unplug the wiring harness, slip off the belts, release the tension springs from the motor carriage with needle-nose pliers, and then unbolt the motor carriage with socket set and remove from the washer. Remove the pulley from the old motor with allen wrench and transfer the carriage to the new motor. Reverse operation for everything and you are back in business. The hardest part was the far back screw holding the carriage, a wobble extension helped.

I took out the two screws in the bottom front panel of the washer, and rotated the front panel from the bottom away from the machine until the top or the panel was released from the machine frame. I then tilted the washer back to get access to the bottom of the machine. The pump pulley had split in half, and the bottom half fell off the drive motor shaft. The only problem I had was breaking free the set screw that holds the pulley to the drive motor shaft. I used a long arm Allen wrench and an adjustable "Cresent" wrench to apply enough force to break the set screw loose. Iclamped the upper transmission belts tightly to keep the motor shaft from turning while I loosened the set screw.

First I unplugged the dryer! Then unscrewed the two screws at the bottom of the front door. To remove the front door, swing the bottom up about 30 degrees until the two triangular hooks at the top of the door release. Then release the two wires going to the door switch from their harness so as to gain more slack to move the door out of the way. The switch was secured by 2 hex head sheet metal screws1/4inch in diameter. I used a small right angle socket wrench to get these loose. I only had to remove the front screw completely to be able to take the switch out for exchange purposes. Once this was done, reverse the process and plug it in! (BTW, the electrical schematic for this dryer is up under the top console)

Remove top two front cover screws. Disconnect wiring. Set aside front cover - door assembly.

Remove two screws at top of the vertical riser cover to expose entire dryer interior. Remove filter. Remove screws to blower cover plate. Remove 4 screws that fasten front drum guide assembly. Remove drum. remove and replace 2 drum support rollers . Replace one rusted drum roller shaft. Replace both drum rollers and non-metalic washers.

Drill out 4 rivets holding two front drum glides. Replace and rerivet new drum glides.

Pry back slighty the many retention points around the front drum assembly which hold the front drum felt seal. Refit the new front drum felt, pressing the retaining clips back in place with a screwdriver.

Replace tumbler motor belt.

Install Drum. Install front drum retention assembly. Install new blower seal with reassembly of blower cover.

Total time - about 1 hour

Replaced the 2 belts according to instructions received with the belts. Very easy repair

From previous experience I suspected the thermal fuse. Turned off the power and removed the front of the dryer by removing the two philips head screws in the door hinge and the two screws on the opposite side of the opening. The front came off easily since all that holds it in place besides the 4 screws are two spring clips. The thermal fuse is located on the side of the chamber enclosing the heating element. I removed the wires connected to the thermal fuse and temporarily joined them together with a spade type connector in order to determine if the thermal fuse was the problem. Turned the power back on and tried the dryer......it ran normally. Turned the power back off and removed the thermal fuse by taking out th two screws with a 1/4" nutdriver.
Ordered a replacement thermal fuse, installed it (with power turned off) and put everything back together. Dryer functioned normally after the thermal fuse had been replaced.
The thermal fuse can be removed and reinstalled using a 1/4" nutdriver. The wires are connected with push on spade type terminals.
Note: The swing damper on the dryer vent (the hooded cover where it exhausts to the outdoors) was jammed in the closed position with an accumulation of lint, which caused the dryer to overheat and blow the thermal fuse. If you experience a blown thermal fuse, always look for the cause or you'll blow the replacement within minutes of running the fryer again.

Cleaned up a wet utility room floor!

Unplugged power cord to the machine and turned off hot and cold water at the stop valves.
Removed the top machine screw that holds the metal panel with the valve attached (on the rear of the machine where hoses attach), removed it from the machine with valve and hoses attached.
Disconnected both water hoses at the old valve, together with the 1/2" hose to the machine. Mark hot and cold positions.
Moved the electrical contacts one-by-one to the new valve.
Changed the old valve for the new valve (one screw attaches to plate).
Connected the inlet hoses and 1/2" hose to the new valve, making sure hot/cold on correct positions.
Replaced plate in the machine and secured with the machine screw.

*** NO MORE WADING SINCE REPAIR *****

1. Unplug power to the washer.
2. Remove 2 screws from bottom front panel on either side. Panel then rotates out and unhooks at the top. Remove front panel
3. Remove bolts from underneath the top front on both sides using a socket.
4. Rotate the top upward to provide space to see and work.
5. From the back of the washer, remove 4 bolts using a socket around the drain tube at the upper left.
6. From the front, the siphon valve can be removed from the inside upper right.
7. From the front, unscrew the clamp holding the drain hose on the water pump housing at the bottom right front and remove the hose. Be prepared for water to drain from the hose. Remove hose and siphon valve together and discard.
8. Install new hose on new siphon valve and screw new clamp tight. Make sure the rubber ring is inserted properly on the new valve (See old valve for reference)
9. Holding the siphon valve in place, use a socket and re-attach the 4 bolts around the drain tube at the back of the washer.
10. From the front, insert the opposite end of the new hose to the water pump at the lower right front and screw the circle clamp tight. Note: Re-use existing clamp.
11. Rotate the top back down into normal position.
12. Plug the power back in and run a short cycle and watch for leaks.
13. If no leaks, re-attach bolts for the top with a socket.
14. Re-attach front panel with 2 screws. Done.

I was told that it might be a clog in the tube.. we check the tubes that wasn't it Then I Google it and was told it might be the drain pump. I was just glad that Part Select had what I need because my machine is over 20 years old. We change the pump and now I hope I get at least another 20 years out of my machine. I will always use part select to get my parts. Thanks

After first unplugging the washer and shutting off the water to the washer I slid the washer away from the wall. It was a tight cramped space and difficult to get behind it. Most of the time replacing the water inlet valve was spent getting into and out of the work area to get tools and cleaning up a few years of dirt under the washer and water leaking from the hoses after they were removed. The valve removal and re-installation of the new one was pretty straightforward.Just a 3 screws 2 electrical connectors and three hoses. The water inlet hoses were frozen on the old valve and required a wrench to free. I also needed to replace the hose washers which fortunately I had as spares for my garden hoses. I replaced the solenoid leads directly from the old to new valve so as not to get that wrong. Removing the outlet hose clamp was tricky- I needed a fat wrench to depress all the tines and slip it off. Fortunately I was able to reuse it. After securing the mounting screws and tightening the inlet hoses with a wrench just until I met some resistance, I turned the power and water back on and prayed there were no leaks. None- back in business.