Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken spring on door.
See GE web site for repair instructions. Take out screws at top of door. Slide unit out there is a spring on each side of the door just look at the good one for details. Easy fix. About 30 minutes.
One axle cracked and broke off; another wheel was had fallen off and was distorted when it hit the heating element.
Removed all 8 wheels and inserted the new one after inserting the axles into each wheel. Replacement wheels had a much better connection to the bottom rack and do not anticipate any problems in the future.
Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking Solenoid valve
1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!
I watched the convenient video and saved an old machine that I've grown to love. Plus I didn't have to pay a repair service or have to buy a new machine. Thanks GE, T. Dunn
I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.
Squeeze the new link to the cable hook with pliers while locking the vise grip to the cable for easier handling. Then, using the vise grip on the cable, hook the other end of the link to the dishwasher door hook
This is a very simple fix. The majority of work comes from getting the unit out of it's enclosed space so it can be worked on. Once the dishwasher is out in the open, lay it on it's side, and simply unscrew some metal clamps, pop out the bad part, replace it with the new, reattach the pieces and clamps, and start putting the unit back in place.
I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.
I'll be back to this site in the future if/when other parts on other appliances go bad.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door seal leaked,and the baffles
removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you
I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..
My husband said it was easy. But the gasket didn't solve the problem. So we had to order another part. We had to order the little black stoppers that go in the hinge area. Still leaked so my husband took them back out and cleaned the area. Then put some kind of sealant in and replaced the black robber things. So far that worked.
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
I first shut off water supply and disconnected the water line and drain hose to the disposal. Then I pulled the dishwasher out from the cabinet unplugged the electrical wire from the wall and laid it on it's back side. I then laid out the new motor and compared parts to parts. It was a direct replacement of the same motor except for very minor changes. I unscrewed the support bracket, then unscrewed the bottom clamp that joined the motor and the rubber connector to the dishwasher. I also decided to replace that part also. That part was removed by using my hand to unscrew it. It has large threads that are not very recognizable when looking at the part. It unscrews counterclockwise like a normal screw. You have to hold the inside piece while you screw the new one back in place. I put it as tight as I could by hand. I would recommend doing so on all motor replacements due to that part not looking so good and if it leaked you would have to take everything apart again to change it out. That part is a separate purchase and it is not included with the kit. Then I took the other clamp to the plastic connector off. I then unplugged the electrical connections, there were only two and they were both exact connections for the replacement motor. After that the entire motor was separated from the dishwasher and I went slipped the new motor into place connected two clamps and made sure everything was reconnected. I slid the dishwasher in place, reconnected the power wire, the drain hose, water supply. I checked for leaks after restoring water pressure. Then ran the dishwasher through a complete cycle and it works just fine. Total repairs cost about 150.00 and the dishwasher appears to be brand new again. I took one look at the diagrams and never had to refer back to them. They had plenty different diagrams and the first option was mine and that was all I needed. I would recommend this option to anyone.
