GLD4100M00CC General Electric Dishwasher - Instructions

Very simple. Took off back cover with screwdriver. Popped off back cap found in center top inside. Replaced spring and white stick looking thing. Put black cover and then back panel back on. Instantly worked again.

Removed the dishwasher from the cabinet. Turned it on it's top side. Removed the exit hose from the pump with a nut driver and replaced the flapper. Reconnected the hose to the pump.

The first posted instruction is dead on (except there are 14 phillips screws (not 10) on inside of door. Also, when reconnecting the 2" quick connect, make sure it is fully inserted - otherwise the numbers on the display panel will not show correctly. Mine didn't the first time, and I had to re-open the door panel and giggle around with the connection to get the numbers to display properly.

This was very easy. 1) roll out lower rack, 2) rotate lower arm slightly counter-clockwise and lift it out, 3) install new lower arm by dropping into position and rotating clockwise. 4) roll in lower rack, and roll out upper rack, 5) use a nut driver to remove the retaining bolt/screw from the upper arm - it's in the center of the upper arm and you have to work from underside of upper rack, 6) remover upper arm, 7) install new upper arm by holding in position and re-inserting the retaining bolt/screw. 8) Tighten the retaining screw and make sure upper arm freely rotates.

I watched the video, read the instructions and went to work. This was the easiest repair I have ever done. I'm 71 and if I can do all 3 spray arms in a total of 15 minutes, anyone can. The hardest part was getting up off the floor when I was finished. The spray arms were all clogged, we have very hard water.

Due to loading a tall item in the lower rack of the dishwasher. The constant hitting of the spray hub, the hub broke.

I purchased the Middle Spray Arm Hub and using a hand nut driver, I unscrewed the nut and attached the new Hub and screwed it back in place.

The replacement was very easy and the cost of the part was very reasonable.

Delivery was quick and the dishwasher was up in running 10 minutes after the part arrived.

I would use this company again and I give them an A+ rating.

Dan Dailey

I had to pull out the built-in dishwasher by removing the top two screws and pulling it out. I unhooked the fill tubing and drain hose. I removed the drain hose hose clamps pulled the hoses off and replaced the new part by attaching the hoses w/ clamps and pluging in the two small electrical wires and it was done. worked great! This was the only site that I was able to find MY EXACT model and the part was a perfect match!!

get fingers between lower spray arm and drive flange - rotate arm counter-clock wise and lift off...the arm was warped and hitting inside of lower door liner.

Open dishwasher and remove the bottom spray wheel, filter, and unscrew the mounting bracket to release the pump connector below the bottom of the unit. Remove mounting screws at top front of dishwasher and carefully slide the unit out; you may have to pry side panels inward with a flat screwdriver in order to get the dishwasher past any cabinetry. Be careful not to pull the dishwasher too far out as the water supply and drain hoses could be damaged. Unplug the unit. Turn unit sideways and tip over onto its' back. At this point, the sump will have to be removed using a nut-driver and/or socket set. This will open access to remove the old pump connector. Replace the old connector with the new connector, and reassemble the sump, connecting and firmly tightening all connectors. Tip unit upright. Screw mounting bracket back into the bottom of the dishwasher and put the remaining parts back. Before pushing the unit back into it's nook, I advise running a quick cycle just to make sure there is no leakage. If there is no leakage, put the unit back, tighten the mounting screws and you're done.

Removed the lower rack and installed new wheels with clips

oversized outlet not available in local stores, this one fit perfectly

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

i removed the screw holding the drain pump to the wire that held the pump to the dishwasher frame, i then unscrewed the hose clamps that connected the pump to the drain hose and the other part of the dishwasher i disconnected the wires , put the other pump into place wired it up and now my dishwasher is as good as new .

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.