7MMSE7999TW0 Maytag Washer - Instructions

Order new hose from Part select. It arrived a couple of days later. I took the old hose off with a pair of pliers, put the new one on ran it thru the hole in the back of the machine and I was done. Total of maybe 20 minutes.

Replace front legs. Very easy fix.

Shut off water and unplugged electricity. Removed hoses, have some thing to catch water in the hoses.
Remove the screws that hold the back cover on the controls panel, and the cover for the electrical cord, you do not have to do anything else with the cord. Remove the 2 screws that are holding the top of the washer to the back panel and slide the top forward an inch or two until it comes loose in the front. Hold onto lt glass top door a lift it up until you can see the silver metal spring clips that hold the controls panel/ cover in place, with a screw driver press the clips back and lift them up a little bit and this will allow you to move the controls panel forward a half inch and the tabs will release and you can tip the cover forward and this exposes the water valve, there are 5 electrical connections on this valve were I to do this again I might order the wiring loom for the valve at the same time that way you would not have to use the small sharp pick to work the connectors loose and reinstall them on the new valve. Replacing the valve was easy as there are only two screws holding it on. Pull up on the valve and it is off.
Make sure all three of the gaskets /prong seals are lined up before you press down on the valve to install it, install the two screws before you plug in the electrical, it makes it easier to tighten the screws. Plug the connectors back onto the valve, 4 on the top of valve on under it and reassemble the washer.

It was a miracle. We were going to get rid of the washing machine because it made so much noise and rattled the whole house. It also 'walked' across the room with every load.
I simply replaced the wear pads (2 of them were already worn away), and now it is as quiet as when it was new. AMAZING!

Replace inlet valve

went really good, received both parts in less than two days, great service! Video's on line were really helpful and made taking apart and putting back together easier, even though video's were on newer model machines. Would not hesitate to order parts from Part Select again.

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

Seal snapped in

My husband was ready to look for a new machine but since it works so well I decided to look on line for the replacement. Found it. Received it in the mail in three days and I popped it in. Thanks!!!

First, I purchased the lovejoy coupling and replaced it, all of the interlocking pins were broken. I suspect that occurred when my wife washed the comforter. Started up the machine and started to smell like the motor was overheating. Also the machine was making a lot of noise (screeching) when it went into spin cycle, so I purchased the clutch. For both repairs I watched the videos and they were spot on and easy to follow. Recommend laying down the washer when replacing the lovejoy coupling, as that was a little tricky trying to do that with the unit upright. The guy in the video must have done that a thousand times to line the up the holes and the pins! Washer is working like a brand new machine!

First I purchaseda new drive coupler and replaced it. Still the drum did not spin. Then I ordered a new clutch but this time when I disassembled the unit I ran power to it after removing the water pump I turned it on and the motor and basket now spun. I found out the water pump was seized so I brought it to my work bench and examined it. When I looked inside I saw a foreign object stuck in the impeller. I took needle nose pliers and worked it out. It was actually a baby's sock from my grandsons recent visit. How it got behind the drum and into the drain hose I have no idea. Once the water pump was freed up, the entire problem was fixed.

I watched the how to video and it was very helpful. I followed all the steps as described although I did not take the cabinet off , I just laid the unit down on the back with a couple towels behind it. the only thing that was a little bit hard was hooking the back clamp on the pump. If you hook the back clamp before putting the pump back on it is much easier.

Looked it up on utube

I am an old woman who is disabled and without any tools or knowledge, but sheer stubbornness and will power, I waited for my tools and other parts to come in, in the mean time I fixed my young neighbors whirlpool washer, well We took top off the nut I had already pre assembled her cam so set it in place of old one put bolt back in place and the top of agitator she says works perfectly now, my parts came in I had nothing to remove as my handicap daughter had already thrown away all the loose parts, I threw away old top agitator, assembled cam and put in place still did not feel tight enough so added seal from other nut!! it worked tight enough, put the inner part back in with new part and soap put the top back on and now works good as new, was disappointed could not put bottom agitator in place, just not strong enough lol well this was my story

Remove top of aggitator, remove bolt 7/16 socket that holds aggitator to shaft. Pull aggitator out of machine. Tip machine on it's side. Remove 2 hoses connected to pump at end of motor. Remove 3 bolts holding gear box to tub frame (1/2" socket).Pull motor and gear box out from under machine. Note where washers, snap rings are on the shaft. Remove snap rings , slide clutch off shaft. Replace clutch , put back together.