7MMSE7999TW0 Maytag Washer - Instructions

Removed the agitator. Then removed the nut holding the agitator shaft. I set the machine on its side. Working from the bottom, i removed the three bolts which hold the transmission/motor. I removed the wiring. Pulling the unit down and out of the shaft bearing. The clutch assembly is on the transmission/motor unit shaft. Remove the snap ring and retaining ring for the shaft. Replace the clutch unit in the reverse order. The hardest part to replace is the retaining ring on the shaft. Pay close attention on how everything comes apart and you won't have any problems. Saved myself a lot of money.

I took the outside case off. took the bolt out of agitator, removed agitator, took motor out with ease of 2 scres and clamps, pulled trannny out and slidd clutch off and put new clutch on. replaced coupling while it was apart with new and better one for 12 bucks. put back together and works like new.......piece of cake........

did not see how it was done husband and son put it together

Removed bolt from agitator assembly. Pulled up on the agitator vane and removed it.
tipped over macvhine . Drained water from tub via the drain hose assemble and removed clips from the hoses to the pump atached to the motor and drained residual water from the lines. Removed the electrical connector attached to the motor assembly and the three bolts holding the motor assembly and shaft to the tub and slid the shaft and assembry out.. Took digital photo of the assembly to insure proper part replacement and removed the clips and spring that are part of the assembly that holds on the clutch. Removed the old assembly and installed the new assembly . Installed the spring and retaining clip that came with the kit and installed the shaft . Installed the three bolts holding the/motor assembly and shaft in place and reconnected the hoses to the pump assembly and reconnected the electrical connector. Uprighted the washer and everything worked like new when I tested the spin cycle. I was quoted $225 to fix the bad clutch from the appliance tech that I paid $20 to diagnose the problem . Saved about $175 by doing it my self and it wasn't hard to do. My thanks to the previous persons that had done the repair and left iinstructions on how to do it.
SW Santa Clarita Ca.

removed the old clutch assembly. Then replaced with the new clutch assembly and it works great.

the original piece had 3 metal clips that held the strip in place. It was a matter of sliding the strip off and sliding the new replacement part on. Time involved was less than one minute. It took longer to find the part than to install it. The part was ordered Thursday night and it was installed by Monday! Great service!

It was simple slide off the old seal and then clip on the new one. I also want to thank the workers at Parts Select, it was very simple and everything went great. I will be using them again and passing the word on.

Ordered the part and a couple of days later I popped off the old and popped on the new. It took longer to remove the part from the box than to install it.

Really nothing to it, especially since the original seal was coming apart. I just ripped it the rest of the way apart and removed it, then slid the new one on in its place.

Very easy --just put it onto the metal and it slipped right on.

Pulled off the old torn seal & in about 15 seconds had the new one put on, couldn't have been easier.

I never have and never will claim to be a mechanic. my wife said it had to be the lid switch. After opening and closing the lid I agreed. Took 2 screws out of back of top panel lifted control panel out of way and there was the lid switch just as part select custumers had said. $100 repairman fix, and I fixed it for a little over $20.

I received the order quickly (although thought it could have been packaged in a much smaller box) and it took less than 10 mins to remove the old seal and replace with the new one. Only problem is the seal I ordered wasnt causing the problem ..lol so will be ordering again!!! Thank you!

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Pulled it apart,layed it down and looked at it,and chaned the 3 springs. And it is like new again. . . . .