Models > 66561619100 > Instructions

66561619100 Kenmore Microwave - Instructions

All Instructions for the 66561619100
91 - 105 of 214
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Clips on grill broke
Removed bed two screw replace grill
Parts Used:
Vent Grille - Black
  • Dan from HOLLY LK RNCH, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old coupling melted and the tray cracked in half.
It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!
Parts Used:
Drive Coupling RING-TURN Glass Cooking Tray
  • Diane from Sheridan, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of hood light bulbs
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together
Parts Used:
Light Bulb - 40W
  • Jerry from Pine, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Vent grill replacement
Unscrewed 4 different screws, replaced the vent & returned screws. Ack to original positions
Parts Used:
Vent Grille
  • Linda from SAN ANTONIO, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light that illuminates the range would not work.
replaced the socket per recommendations on this web site. this did not correct the problem.
Parts Used:
Light Bulb - 40W Light Bulb Socket and Housing
  • bob from SEBASTIAN, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old vent fell apart
Slipped in and screwed top on
Parts Used:
Vent Grille
  • george from GULF BREEZE, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The air filters were fine. The Front grill did no or could not fit. It too big however, not bu much, just enough so it will not fit the space. If it could fit the space with enough room to close the door I could screw it in
PRAY !Pray hard
Parts Used:
Vent Grille - Biscuit Charcoal Air Filters
  • Cleveland from CAPE CORAL, FL
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turntable did not work
Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.
Parts Used:
MOTOR-TURN
  • Eldon from ORANGE, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Exhaust Grill cracked
Simple repair. Remove 6 screws to remove old grill and replace with the new grill using the old screws.
Parts Used:
Vent Grille - Biscuit
  • Donald from BECKLEY, WV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very unusual. we had a brief fire inside the microwave which destroyed all the moving rotary parts.
First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple
Parts Used:
RING-TURN Drive Coupling Glass Cooking Tray
  • Jan from ELK GROVE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the wheels came off
Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul
Parts Used:
RING-TURN
  • Paul from EXETER, NH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive coupling cracked would no longer rotate turntable plate
used screw driver to pry up old part. lifted right off. line up drive couple drive push on. repair took less than 1 minute to repair. works like new
Very Pleased with Parts Select replacement parts
Parts Used:
Drive Coupling
  • Edward from CENTENNIAL, CO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
existing vent grill cracked
the new part fit just right. put in place and screwed in with existing screws. like a glove.
Parts Used:
Vent Grille - Biscuit
  • ROBERT from LEESBURG, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave vent cover broke as it was cleaned.
Bought a new one. Perfect match, easy replacement.
Parts Used:
Vent Grille - Black
  • Paul from FRANKLIN, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke rotating plate, it fell off counter after being washed
Opened door and put new plate in.

Placed order on Thursday evening and received Sat Am
Parts Used:
Glass Cooking Tray
  • Lois P from Morris, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 66561619100
91 - 105 of 214
Back to Top