25344302400 Kenmore Refrigerator - Instructions

First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.

1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place.
2. Removed and drained all water lines.
3. Removed three electric solenoid wiring connections.
4.Cut and marked all water lines to facilitate new connecting procedure (instructions provided with the new valve assembly).
5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings.
6. Clean the embarassing dust from under the appliance!!!

Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.

Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.

You pull out the tray at the bottom of the space in the freezer door where the ice and water are dispensed. The tray didn't come out easily, but don't be afraid of breaking anything. It is a simple interference fit. Then remove the two phillips screws at the bottom of the face plate and lift it gently. It can dangle from it's electrical connector while you do the rest of the job. Remove three phillips screws that hold the rest of the assembly in place. No need to completely remove the assembly. Do not disconnect the water tube. Disconnect the power plug at the left so that you can pull it out a little farther and not have to worry about shorting anything. The water actuator is secured by two small plates with two phillips screws and there is a spring too. Remove the screws and plates. There is also an electrical connection. The wires were installed under a relay at the factory so I had to trace the wires, disconnect the plug, and then snip the wires to remove. It's crowded in there so you have to work it around to get the actuator out. Then replace it with the new actuator. Reconnect the electrical and make sure the spring is in place. Then just go backwards. Put the plates back on, reconnect the power plug, screw the assembly back in, put the face plate back on, and slide in the tray back in. You might want to test the water and ice after you reattach the assembly but before the face plate. I needed the hemostat when I dropped one of the screws into the assembly. Needle nose pliers would work just as well or just don't drop anything.

This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having.
The fix was easy just a few wires cut and spliced and viola fixed.

1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

I pulled out all the screws and from the freezer side and remove the panel, then I located the thermostat snap the old one out and put the new one in.

Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...

This could not have been easier. I came to this website looking to see how much the part was before i called a repairman to come do it. I saw everyones instructions and decided to try it myself. To replace the ice maker you basically unscrew 2 screws, unplug the broken one and remove it. Plug in the new and tighten the screws to hold it in place. I would have been REALLY unhappy if i had called a repairman and saw that was how it was done.
Could not have been easier

Put in new hinges and two screws

The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others.
Take care-Bill

Unscrewed the water line cover. Removed the platic case around the water filter base. Everything went well until I tried to remove the two water hoses. After I finally figured out that I had to push in the release washer while pulling the hoses out, things went well. Unfortunately it took several hours of wasted time and several searches on the internet to finally figure this part out. From there on out it went smoothly. Old base came out with two screws. Reversed process for reinstall of new base. Water hoses just slipped back into place and locked themselves in. Just takes a little patience.

The symptom was a fried power board located in the freezer door behind the ice/water dispenser. Replacing the board was fairly easy. However, the new board also cooked soon thereafter. I discovered that the root cause for this failure was a failed diode Part Number 5303918287. The diode is located in the wiring near the three water solenoids in the rear (lower right) where the water enters the unit. Unless the diode is also replaced, the board will fail again.
Replacement of these components is fairly easy. One trick that work well for me during re-assembly was to use a long wood screw to thread up through the water dispenser panel and into the end of the water tube, and then pull on the screw head to gently feed the tube down into the dispenser.

The radiator was not being properly defrosted and the refrigerator and freezer could not keep the temperature. Two things can be causing this, the defrost module which defrost the refrigerator on a regular basis ($110) or the thermostat ($18). I tried the thermostat since it is very easy to do (remove cover plate inside the freezer, cut wires of old thermostat, connect new thermostat by stripping wires. Presto...however the thermostat was NOT the problem. The problem was a blown timer circuit board that controls the regular defrosting. That repair was done by a technician. The board was $110, it seats inside the refrigerator in the control panel area.

Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of water

When the ice maker is over filling, either the valve is defective or clogged, or the ice maker is at fault signaling the valve to stay open too long. My problem was the latter. I had already replaced the valve, thinking that being only 2 years old, how could the ice maker be faulty. I was wrong. Ice maker unplugs and comes out with 2 screws. A quick swap with the new ice maker and all is well. Simple