22305 - Instructions

Shut off power. Removed screws holding panel.Removed wires from old switch.Installed wires on new switch and reinstalled panel.EASY

You probably want to look inside as you read this. Most of it is straightforward, except the retaining clips.

First, I turned off the breaker switch. Opening the control housing, I disconnected the two leads and wrote down their orientation (one is silver, the other copper). In my JennAir model, an orange burner light is on either side of the fan switch. The white plastic on the rear is held on by their keyhole shape - just slide them the only way they can. This gives extra working room.

Since the switch plastic was already decayed, I snapped off the whole central square unit leaving the 2 portions held onto the posts by the metal retaining clips. Using a small flathead screwdriver, I pried up the plastic remnants, working around it until the retaining clips came loose/ broke.

The new unit fit perfectly and easily. The new retaining clips needed to be worked down a small circular file to spread the centers out enough for me to work onto the retaining posts. The file was just barely bigger than the existing hole. The clips can be broken if you are too rough or work them too much. After that, I used a pair of snub nosed pliers to push the clips down the posts. They required a considerable amount of force, but they aren't going anywhere anytime soon.

Reconnect the lights, reconnect the 2 leads, and check for any loose wires from other controls and loose parts. Reseat the control housing, turn on the breaker and test.

just replaced by hand .

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

used the supplied parts...very easy. The parts were exact replacements.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridge base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Replaced the drip pans

so easy, just ordered the part, the part came and inserted the element into the stovetop

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.

Pulled out the old burner and plugged in the new!

removeed the dial cover, paced the lens into the hole, slid the light and holder into place , 5 min job.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover