22305 - Instructions

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

No repair, lol! Just a perfect fit for my ignition :). I bought two in case my grandson gets curious again.

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. T ... Read more he springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

Had to drill out screw for old connector bracket and also had to extend wires from controls this took most time. Once done with this used wire cutters to strip back insulation and then put the whole mess back together also used a larger wire nut to reconnect wires.

The burned control switch was not functioning. It took a while to find the range model number and then the part number of the switch. It was cool that I could see a picture of the part with the part number on the internet so that I was sure to buy the right part.
Once the part arrived, I turned off the power to the range (circuit ... Read more breaker, 220 V) removed two screws, used nut driver to disconnect switch handle, marked the 5 wires going to the switch, used the needle nose plier to remove the wires, the attached wired to the new switch, placed switch back into position, used nut driver to attach switch to the control unit. Rescrewed control unit in place with two screws.
turned on circuit breaker and tested. All good.
It is clear that this old Jenn Air range and be completely redone to good as new. All parts are available

disassemble housing and remove fan and motor. Reatach fan to new motor, connect wiring, place gasket around motor and reassemble.

removed burner and recepticle and replaced new one. You don't have any place to comment on service, so I'll put it here. I talked to Herb and ordered parts with him on a Monday afternoon. He was very helpful. The part came Thursday about noon and I immediatly installed parts and my wife cooked supper (thats southern for the evening mea ... Read more l) that night. A really wonderful experience. Thank's Herb.

After I removed the piece of metal separating the two wires, I inserted the unit with no problem.

Our stove is from 1978 and was missing all but one drip bowl. I bought all the replacement parts from all the store, (Walmart, Target, Fred Meyer) nothing fit. I finally found this site and they fit perfectly! Thank you. If I have to keep the stove a while longer at least it looks clean and new now, and it still works great!

Simply removed the old heating element and plug the new element terminals into socket.

Unplugged old burner element, plugged in new element.

SHUT OFF BREAKER! Remove exhaust grill and switch knob. Remove cooktop switch panel by removing two screws and sliding panel toward exhaust grill. Remove switch retainer nut with deep socket. Transfer wires one by one to new switch. Install new switch tightening retainer nut. Reinstall switch panel with two screws, push knob onto sh ... Read more aft. Turn on breaker.

our cook top is so old, but no need to replace just yet. so I ordered new knobs to get a new look
thank you!

I pulled off the other 3 old knobs. Pushed on the new ones, which pushed on hard, but work. They stick out farther than the originals. They look a little different, but only to me. No one else would notice.
The main part is, it works. A little spenty for my taste, but did not know where else to go and they arrived very quick.

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get ... Read more it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.