The function of the grease filter is to trap grease into the filter from the exhaust air. The grease filter is intended to be used with certain downdraft cooktops and ranges. This grease filter is roughly fourteen inches long and almost twelve inches wide, and chrome in color. Removing your old grease filter and replacing it with a new on...Read moree is an easy job, users say it took them less than fifteen minutes to install. We recommend that when removing your current grease filter, you use work gloves to protect your hands and clean the entire area thoroughly before installing the new filter.
This is a drip bowl, and it is used in conjunction with your range. The function of this part is to sit underneath your stove top burner element. This will allow the bowl to catch any spills that fall through the burner while cooking. This model is chrome has a chrome color trim, it measures 8 inches in diameter, and is sold individually....Read more Before installing this part, you must wait until the surface of your range is cool to the touch. Replacing the drip bowl will require you to touch the burner on your stove top.
The drip bowl is found under the 6-inch burner on your range. This square chrome stove top drip pan is intended for use with electric ranges. It has a 2-inch inner hole diameter and 7-inch outer diameter. Drip bowls should be cleaned regularly, and replaced when too much food and debris has been burned or stuck to it, making it too hard t...Read moreo clean. You should replace your drip pan if it is rusted or damaged. Grease, oil, and food can spill into your unit and become a fire hazard. This drip pan is dishwasher safe and is sold individually.
The tools you will need to replace the surface burner receptacle kit on your range include a Phillips screw driver, and a pair of wire strippers. Before doing this repair, make sure to disconnect your appliance from the power supply and wear work gloves to protect your hands. The surface burner receptacle kit comes with a plastic block, h...Read moreigh temperature wire nuts, a metal bracket, and wires. This part functions as the connection between the wire harness and the surface element in your range.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the left or right hand side of your oven, and is approximately 20 1/2 inches long. If your oven door will not open or close easily, you may need to replace this part. It may be a good idea to repl...Read moreace both hinges at the same time. If a spring has become loose on one hinge, the other hinge is likely to have the same issue. The repair is simple and only requires a Phillips screwdriver and a small bent nail. For a full step-by-step guide, check out the video below.
This 8 inch surface burner with reinforced delta frame carries 2100 watts and 240 volts. It has five turns and is compatible with many electric ranges. Its center medallion is all black in color.
The surface element control switch is an essential component in electric ranges, responsible for regulating the heat output of the surface burner. It allows you to adjust the temperature levels by controlling the electrical flow to the burner. If your stovetop burner fails to turn on, stays on high heat, or doesn’t respond to adjustments,...Read more a faulty switch could be the cause. This switch features a double flat shaft design and is nut-mounted for secure installation. Always disconnect the power supply before replacing the switch to prevent electrical hazards. Ensure compatibility with your appliance model before purchasing.
This is a delta frame surface unit, also known as coil element, for a stove, range, or oven. It is a 6-inch surface burner with a reinforced delta frame that carries 1250 watts and 240 volts. The burner has four turns and is compatible with many electric ranges. The center medallion is black in color. The burner provides heat to your cook...Read moreing area to cook your food items. If your burner is not heating properly, you may need to replace it. Be sure to disconnect power to the appliance before completing this repair.
This set of four burner knobs helps control the heat on a range or cooktop. Each knob fits a double-flat control shaft and shows the burner settings clearly. Replace the knobs if they are cracked, loose, worn, or missing. Before ordering, inspect each shaft for bending or damage. A new knob will not fix a bad burner switch. Confirm fit wi...Read moreth the full appliance model and shaft shape. Turn every control to Off, disconnect power, pull the old knobs straight off, and press the new ones on without force. Check that each pointer lines up correctly.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
replaced filter
486 of 513 peoplefound this instruction helpful.
ELOISE from MILFORD, OH
Really Easy
Less than 15 mins
pulled old one out , cleaned the area & replaced with the new one.
Was this helpful?
Thank you for voting!
Old grease filter that I actually did not know I had to change
451 of 540 peoplefound this instruction helpful.
deborah from fort pierce, FL
Really Easy
Less than 15 mins
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Was this helpful?
Thank you for voting!
Stove top element not working due to bad receptacle.
195 of 215 peoplefound this instruction helpful.
Richard from Carthage, NC
Really Easy
Less than 15 mins
Pliers, Screw drivers
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit. My sister
... Read more's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts. The element is working great now. Whenever I need appliance parts again I'll use partselect.com.