Whirlpool Dryer Switches

Videos!

Your Price

$27.36

Whirlpool Dryer Door Switch

★★★★★

508 Reviews

PartSelect Number PS11741701

Manufacturer Part Number WP3406107

This dryer door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open, and operates the drum light. White in color and 6.5 inches long, this OEM switch is comprised of plastic and metal, and features the switch and three wires that comprise the part. Sold individually, this part attaches to the inside of the top end of the front panel. One end attaches to the wiring harness, the other goes through the panel to make contact with the door when the door is closed. Over time, this part can be subject to material fatigue or breakage due to frequent use or rough handling. If it breaks or is defective, you won't be able to start or stop your drying cycle, depending on the position your switch broke in. The easiest way to test this part for functionality is to test it by hand. Push on the black tab that sticks out of the front panel to make contact with your dryer door; if there is no resistance in the tab and it doesn't make a click sound, you may need to replace it.

Fixes these symptoms

Door won’t close
Drum Not Spinning
Light not working
See more...

Installation Instructions

pat from lisbon,, OH

door switch was bad

i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service Read more...

Videos!

Your Price

$59.47

Whirlpool Dryer Push-to-start Switch

★★★★★

17 Reviews

PartSelect Number PS11748542

Manufacturer Part Number WPW10117655

This switch or push to start switch is used for dryers. It is the tool that completes the circuit and ultimately starts the dryer by pressing and releasing the button after selecting a setting on the timer. The tools needed for this project are a 1/4 inch nut driver, and a flathead screwdriver. To repair, first remove the rear panel and start switch. Next, replace with new start switch and rear panel. Remember to unplug your dryer before beginning this installation and refer to the manual provided by the manufacturer for further installation instructions.

Fixes these symptoms

Won’t Start
See more...

Installation Instructions

Josh from Emory, TX

Push to Start switch burned out due to electrical problem

Unplug from the wall ,remove upper back panel ( watch out for the grounding wire screwed to the panel), pulled off front knob, then twist and pull the switch out. Unplug the burned out switch, plugged in the new one. Re-assembled what I took apart, plugged her up and dried the load that was in the washer. Note: if yours is burned out due to house power surge make sure the timer is working after you replace the switch, you might need one of thoes too. Read more...

Videos!

Your Price

$28.42

Whirlpool Dryer Push-to-start Switch

★★★★★

20 Reviews

PartSelect Number PS11742178

Manufacturer Part Number WP3977456

This push-to-start switch activates the dryer when the button is pressed and released. If your switch is not turning on or off, will not start, or the contacts inside the switch are shorted out, it is best to replace this part as a possible solution. Remember to unplug your appliance before beginning the installation process, as safety precaution. For installation instructions and accurate guidance, refer to the diagram provided by the manufacturer.

Fixes these symptoms

Touchpad does not respond
Won’t Start
See more...

Installation Instructions

Dennis from Port Orchard, WA

Broke start switch while moving

Turned off the power.Pulled the dryer out, removed the screws from the control cover panel, unplugged the switch, pressed the release clip the did the opposite to install new switch. Replaced the back panel, put the nob on and it looks as good as new.Turned on the power. Read more...

Videos!

Your Price

$27.36

Whirlpool Dryer Rotary Start Switch

★★★★★

63 Reviews

PartSelect Number PS3487203

Manufacturer Part Number WE4M519

This replacement start switch is a genuine OEM part for your dryer. If your dryer will not start or shut off, you may need to replace this part. For this repair you will need a number 2 Phillips screwdriver and a pair of needle nose pliers. Disconnect power to the dryer before beginning this repair.

Fixes these symptoms

Will Not Start
Won’t Start
See more...

Installation Instructions

Mr Dennis from Twinsburg, OH

Knob would not engage, had to manually turn outer ring to start washer.

Used a screw driver and needle nose pliers to remove clip from behind the timer knob. Took 2 minutes to remove clip, i admit it was a little tricky but once you get a grip on the clip very easily removed. Replaced with new knob, old knob gear was completley stripped . put the new clip on and presto, Like brand new.A normal service call would of ran me 45.00 just to tell me what was wrong with the machine. Read more...

Videos!

Your Price

$27.36

Whirlpool Dryer Door Switch Assembly

★★★★★

49 Reviews

PartSelect Number PS11741700

Manufacturer Part Number WP3406105

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

Fixes these symptoms

Running With Door Open
Won’t Start
See more...

Installation Instructions

John from Bethesda, MD

Dryer would stay on after opening the Door. The switch that turns off the dryer when you open the door was not broken.

You open up the lint filter access door and remove the two small screws that hold it to the top of the dryer. Once they are removed, you insert a flat blade screwdriver under front-top of the unit and the top will pop off. Exerting a little pressure towards you will help lift to top off the mounts. There are no other screws to remove.
The new switch comes attached to a clip. You just pull off the old clip and replace it with the new one and discard the old switch. Read more...

Videos!

Your Price

$22.52

Whirlpool Dryer Lid Switch

★★★★★

17 Reviews

PartSelect Number PS11723153

Manufacturer Part Number W10820036

This washer/dryer lid or door switch kit serves as a critical safety component, designed to prevent the appliance from operating when the lid or door is open. It ensures that the washer does not fill or spin and the dryer does not start unless the door is securely closed, helping to avoid water spills and potential safety hazards. The kit includes all necessary components for installation and is compatible with a wide range of top-loading washers and front-loading dryers. Installation typically involves disconnecting power, accessing the control panel or door area, and replacing the switch using standard tools. The switch is compact and designed to fit seamlessly within the appliance’s housing, with dimensions approximately 2.5 inches in length, 1 inch in width, and 1 inch in height. It features a neutral color finish that blends with most appliance interiors.

Fixes these symptoms

Will not agitate
Will not drain
Will Not Start
See more...

Installation Instructions

Peter from Westbury, NY

washer would not start

To see if the lid switch was the problem I first jumped it out and tried to start the washer. That was the problem. I removed the main controll so I could get to the lid switch. I made the mistake of removing the screws all the way out and the metal clip fell into the body of the washer, no problem since I was changing the drive beld anyway. I realized that you do not remove the screws all the way out, you just have to loosen them and then slide out the lid switch & then replace it. Read more...

Videos!

Your Price

$44.23

Whirlpool Dryer Door Switch

★★★★★

11 Reviews

PartSelect Number PS11750824

Manufacturer Part Number WPW10237959

This is a door switch that is compatible with models of dryers. The door switch in a dryer is designed to communicate with the control board when the door is open or closed. If this door switch is damaged or not working properly, it will cause your dryer to incorrectly detect whether the door is closed and will normally result in your dryer not being able to start or stopping a cycle randomly. This door switch is made entirely of plastic with the door switch tab on one end, and its wire harness on the other. Replacing this door switch is easy but does require some slight disassembly of your dryer, which you will need a screwdriver and wrench for. This door switch is an OEM part and does not come with its necessary securing screws.

Fixes these symptoms

Running With Door Open
Won’t Start
See more...

Installation Instructions

Ronald from LANCASTER, CA

A piece of cloting snagged and broke the door switch.

Repair job took less than 10 minutes: 1) Unplug Dryer 2) Remove Lint screen and 2 Phillip screws 3) use flat putty knife to depress lid latches while lifting (latches located approx 2 - 3 inches from each side. 4) unplug defective door switch 5) remove 2 Phillip screws that secure the door switch. Reinstall switch repeating the above steps in reverse order and your done. Read more...

Videos!

Your Price

$24.67

Whirlpool Dryer Door Switch Kit

★★★★★

20 Reviews

PartSelect Number PS1964648

Manufacturer Part Number W10169313

This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble, replacing the door switch can solve this appliance problem. The tools needed for replacement are a screw driver and wire strippers. Make sure to attach the two wires to the right two poles of the new switch, to do this you can check the resistance of the switch. Unplug the dryer before installing this part, also refer to the diagram provided by the manufacturer.

Fixes these symptoms

Noisy
Running With Door Open
Won’t Start
See more...

Installation Instructions

Don from Jacksonville, FL

Switch sticking in on position

FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two screws, one on the left side, and one on the right, remove these screws, and pull slightly down on panel to remove. Behind this panel find two screws holding the door panel, one on the left, and one on the right, remove the left, and support the door panel while removing the right side. Gently pull the bottom of door panel outward, and the clips on top of door panel will unhinge from top, carefully rotate left side of door panel to floor, and note the wire connections on switch, and orientation of switch, then unplug wires, and move door panel to a comfortable working positon. Door must be open to remove switch, then depress the two plastic retaining keepers on each side of switch, and push switch through toward door. Replace with new switch, reconnect the wires, and reassymble in reverse order. Remember, door assymbly must be inserted in dryer top at an angle, and then bottom rotated downward, and bottom panel nylon guildes inserted into door panel bottom. Read more...

Videos!

Your Price

$39.46

Whirlpool Dryer Door Switch

★★★★★

8 Reviews

PartSelect Number PS2344321

Manufacturer Part Number WE4M415

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

Fixes these symptoms

Won’t Start
See more...

Installation Instructions

Joshua from Dallas, TX

Dryer would not start

The end repair was very simple and took minimal effort. The time and difficulty was all in the testing. I disassembled the dryer and removed the drum and then hard wired each thermo-fuse to determine where the fault was. After test all of those I was stumped. When I opened the door the light would not come on so I assumed it was a power fault closer to the source. However after all of my testing I couldn't find anything wrong. I then removed the light bulb and realized it was burned out which led me to the door switch being the fault. I removed the switch and soldered the three wire together and the dryer started right up! All I had to do was order a new $15 part, unsolder the wires and plug them in. Would have been so much simpler if that light bulb hadn't of been burned out causing me to over think my diagnosis. This was my first major appliance repair and I did it with only the help of the parts diagram provided on the website. Read more...

Videos!

Your Price

$64.69

Whirlpool Dryer Start Switch

★★★★★

9 Reviews

PartSelect Number PS11754857

Manufacturer Part Number WPW10446920

The push-to-start switch activates the dryer when pressed and released. Compatible with select dryer models, this part ensures proper functionality. Verify fitment before ordering, as similar parts may have slight variations. Disconnect power before installation and use protective gloves.

Fixes these symptoms

Won’t Start
See more...

Installation Instructions

Thomas from LOWELL, MI

Replace start switch

Take back off top of dryer and replace switch Read more...

Shop by Department

Top Appliance Brands

Top Lawn Equipment Brands

Popular Whirlpool Dryer Switches

Related Whirlpool Dryer Parts

Shop by Department

Top Appliance Brands

Top Lawn Equipment Brands

Sample Model Number Tags

EasyApplianceParts is Now PartSelect!

Whirlpool Dryer Switches

Find Your Part

Popular Whirlpool Dryer Switches

Related Whirlpool Dryer Parts