This dryer door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open, and operates the drum light. White in color and 6.5 inches long, this OEM switch is comprised of plastic and metal, and features the switch and three wires that comprise the part. Sold individually, this part attaches to the inside of the top end of the front panel. One end attaches to the wiring harness, the other goes through the panel to make contact with the door when the door is closed. Over time, this part can be subject to material fatigue or breakage due to frequent use or rough handling. If it breaks or is defective, you won't be able to start or stop your drying cycle, depending on the position your switch broke in. The easiest way to test this part for functionality is to test it by hand. Push on the black tab that sticks out of the front panel to make contact with your dryer door; if there is no resistance in the tab and it doesn't make a click sound, you may need to replace it.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Yolanda O - 24 days ago
Verified Purchase
Easy Repair
Part was the correct one and thanks to the do it yourself video I was able to fix it myself in 20 minutes.
★★★★★
★★★★★
Maryanne Y - October 1, 2023
Verified Purchase
Easy Repair
It took a little longer to get the door switch for my dryer, but once I got it, it was very easy to replace. Just watched a YouTube video. My dryer works great !!
★★★★★
★★★★★
Tabitha G - September 30, 2023
Verified Purchase
Easy Repair
Fixed the issue in one try! Part was well made and arrived quickly. I love the addition of a tutorial video. Will use partselect again.
★★★★★
★★★★★
Thomas S - September 18, 2023
Verified Purchase
Easy Repair. You Tube Video Instructions Good. Dryer working again.
Part was correct. Received fast. thank you!
★★★★★
★★★★★
Sergio R - September 8, 2023
Verified Purchase
Easy fix
Appliance working again
★★★★★
★★★★★
Jay B - September 1, 2023
Verified Purchase
easy repair
Easy to find the part on the website; while it was a bit overpriced, it arrived on time (quickly) and repair was easy
★★★★★
★★★★★
Erica S - August 18, 2023
Verified Purchase
Easy repair for a novice
It went great! I especially appreciate the videos on the website that gave me step by step instructions.
★★★★★
★★★★★
Tim C - August 13, 2023
Verified Purchase
Perfect Replacement
The part was a direct replacement and very easy to install.
★★★★★
★★★★★
Janine T - August 3, 2023
Verified Purchase
Just what we needed and delivered FAST!
This switch was exactly what we needed and installed easily. It was delivered just a few days after we ordered it!
★★★★★
★★★★★
Anthony L - July 18, 2023
Verified Purchase
Easy repair following most helpful instructions
The part was new and arrived on schedule and fit perfectly. Appliance works properly.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 137 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dryer would not turn on and when dryer door was opened it would not turn off
First, I replaced the door switch. Removed 2 screws for the lint catcher and then pryed up both front edges to lift the top. Remove 2 screws for switch disconnect the switch and replaced. Second, I replaced the push to start switch. Remove 6 bolts on back panel and remove. Remove locking clip from switch and pull out switch and replace. Reinstall switch and locking clip put knob back on and install back panel. DONE
Your video of the door switch replacement makes this job easy! My recommendation watch the video and you will have the switch replaced in a short time! My dryer was older than the dryer in the video but the principal of repair is the same! My new switch replacement fixed my dryer so when the door is opened the dryer shuts off!
Light won’t come on when dryer door is opened & drum won’t stop when door is opened
Kill power to dryer from breaker box.Remove lint filter & 2 screws. Take a flat head screw driver and place in gap between rash from corner of top panel & front panel of dryer and pry up to raise top panel of dryer & rest against wall the wall on angle do it doesn’t fall back toward you. Unplug wiring harness from dryer switch inside top front corner of dryer with outside of drum exposed when top panel of dryer is raised. Open dryer door and remove screws on each side of dryer switch located at upper inside corner of door opening. Take flat head screwdriver had slide in between connector & wiring harness on dryer. Remove old switch. Reconnect new dryer switch to wiring harness & remount switch to inside of dryer door opening. Lower top panel of dryer & press front corners of top panel to front panel of dryer & clips will be locked in place. Replace screws in dryer filter mounting holes yo top panel & replace dryer filter in place. Turn on power ‘ & check if light is working 1st. Then, turn timer knob clockwise, close door and listen if the drum is turning. Open door to see if drum turns. If both work, the job is complete.
John from LINDALE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced bulb, door switch and heating element.
I followed the instructions that I watched on the video. The video was very helpful.
1st- installed the push to start switch-was not the problem 2nd installed the dryer thermal fuse and was not the problem 3rd installed the dryer door switch and the dryer started right lup
Installed new door switch, so, so simple. Unplug dryer, remove lint screen, undo 2 scews located at base of lint screen opening. Use flat head screw driver to pry up dryer top, once open, rest the top against the wall. Now you will see the door switch in the right hand corner at front of the dryer.Open the dryer door , remove 2 screws holding the broken switch, disconnect wire from dryer, click in the new switch, put everything back together, plug in the dryer and go! Super quick and easy, wish I had just done this months ago!!!!
Aaryn from HUNTINGTN BCH, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer switch was broken
I just followed the instruction in the video, step by step. Easy as pie. Took out the screws, raised the top, unplugged the switch, took it out, put the new one in. Then reversed the process and put it all back together. Of course, always unplug the dryer from the wall plug before you do anything. The light bulb wasn't bad and came back on when I replaced the door switch. Now I have a replacement if it goes out.
Per instruction video and past experience. Part replacement came quickly (2days from purchase) and the correct parts were sent. Dryer works better now than it did new.
Noticed the door switch was loose and the light bulb inside dryer didn't stay on. Researched the problem on PartSelect. Followed the directions given: Take 2 screws out of top of lint trap. Pry top off of dryer with putty knife. Unscrew 2 screws in dryer door frame holding in old switch. Uplug and remove old switch. Plug in new switch and put screws back in. Close top of dryer. Reinsert 2 screws in lint trap. My 20 yearn old dryer works!
Linda from SANTA MONICA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door switch broken, the dryer would not stop when I opened its door
There are many good youtube Kenmore/Whirlpool door switch replacement demos online. The one already done by this site )was close enough for me. I could see that the door switch on my dryer was bad (the plastic part that the door makes contact with was visibly broken, as seen from the outside) -- so I ordered a new one. You don't have to open the top fully to access the switch wiring harness -- i propped it open with a roll of duct tape, The hardest part for me was to disconnect the old switch from the harness (I used a small flat bladed screwdriver to free it). Be careful, the metal inside the opened dryer is sharp, and can cut you.
James from Crawfordville, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
82 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lindsay
July 20, 2017
Im replacing the door switch assembly for my dryer and I know I have the right part for my model bc I confirmed it with you first. However when I removed my old switch assembly it has two wires, but this replacement part has three. Whats going on and will this change anything?
Hi Lindsay, the third wire will not make a difference. It is for the drum light and will not be in the harness. This part has been redesigned by the manufacturer to work with several different types of dryers, which is why they now include the third wire. I hope this helps!
188 people found this helpful.
Was this helpful?
Thank you for voting!
Drew
July 20, 2017
My dryer won’t stop spinning unless I turn it off. Is this what I should be replacing?
Hi Drew, yes, it sounds like you need to replace the door switch WP3406107 on your dryer. Best of luck with this repair!
92 people found this helpful.
Was this helpful?
Thank you for voting!
Neal
August 14, 2017
When dryer door is opened, the dryer continues to run and light does not come on. Is it the door switch?
For model number lgr8648lw1
Hi Neal,
Thank you for your inquiry. It definitely sounds like it would be your door switch that is the problem. You can test it with a multi-meter to see if it is malfunctioning. Good luck with your repair!
42 people found this helpful.
Was this helpful?
Thank you for voting!
Bob
October 11, 2017
Would this defective part also cause the light to not go on when the door is open?
For model number 850JQ0
Hi Bob,
Thank you for your question. Yes, if this part was malfunctioning, generally your light would also not come on as well. Good luck with your repair.
21 people found this helpful.
Was this helpful?
Thank you for voting!
Marcy
December 17, 2017
Dryer does not come on when I hit the start button, it will work if i push in very firmly on the door. Before it was working, but would stay on even with the door open.
For model number LGB86300PW0
Hi Marcy,
Thank you for your question. It sounds like you will need to replace your door switch. When that part is not working it will not allow your appliance to start for safety reasons. Good luck with your repair.
21 people found this helpful.
Was this helpful?
Thank you for voting!
Karen
August 24, 2017
While checking the door switch i have a open reading is that right? If so what do i check next? I have replaced the fuse.
For model number RED4440VQ1
Hi Karen,
Thank you for your question. If your door switch is reading as open, then that would mean that you have an open circuit and that the part does not have continuity. You may have to replace that part as it seems like it is malfunctioning. I would not be able to say what else it could be because I am not sure what your issue is. Good luck with your repair.
15 people found this helpful.
Was this helpful?
Thank you for voting!
Neil
July 20, 2017
So my wife told me that the dryer was not staying on and the door switch was a little faulty so I replaced it. But now that its been replaced it is still turning off randomly. What should I look at next?
Hi Neil, it sounds like you have a faulty motor that needs replacing. Please let us know if you have any further questions.
9 people found this helpful.
Was this helpful?
Thank you for voting!
Bert
November 14, 2017
The heating element for the dry stays on when the door is open, but the dryer does not tumble when the door is closed. Could this possibly fix the problem?
For model number WED4800XQ1
Hi Bert,
Thank you for your inquiry. If they dryer is not shutting off when the door is open then the door switch should fix the issue. Some other parts you will need to check as well are the internal bias thermostat, the thermal fuse, the heating element, the motor and the timer. I hope this helps. Thank you and have a great day!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Julia
August 26, 2017
I have a Whirlpool dryer, i think it's the door switch that needs to be replaced but when my husband and i test cycle and stop, we open door and smelt like a burning smell.. what could cause that?
Hello Julia, thank you for contacting us. If it is a rubber burning smell it could be the belt slipping, and may need to be replaced. If it is a burnt electrical smell it could be coming from the motor. You can do a visual inspection of the belt to determine if it is bad and needs replaced. Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Abe
November 6, 2017
How to switch the opening of the dryer door
For model number 3ZMED5705TW0
Hi Abe,
Thank you for your inquiry. There is a video listed with the part on our website that will show you how to install the door switch. I hope this helps. Thank you and have a great day!
7 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11741701
Manufacturer Part Number: WP3406107
