Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
JERRY B - June 23, 2020
Verified Purchase
Promp service.
The part was received quickly as promised. Installation was relatively easy. However adjusting the unit proved to be very frustrating. Barely touching any of the 3 screws made the speed very erratic. I was able to get constant speeds at all but level one, where the unit surged. Apparently there is more wrong with the mixer than just this part.
★★★★★
★★★★★
Josephine B - January 8, 2023
Verified Purchase
Works great
I didn’t have to wait to long for the part, great condition and fairly easy to install.
★★★★★
★★★★★
JOHN W - December 18, 2018
Verified Purchase
How to get to the speed control plate
The repair was easy when I figured out how to get to the switch.You only have to remove the one screw on the cover at the back end of the mixer. Be careful. There is a spring that you have to disconnect. It is down by the bottom screw of the switch. This screw also is an adjustment screw for the switch. Hope it helps you do this repair. I had never done it before.
★★★★★
★★★★★
Patrick B - October 15, 2018
Verified Purchase
speed control plate
Fit great worked great mixer back in action thanks
★★★★★
★★★★★
James Z - March 17, 2018
Verified Purchase
The repair only took about 15 minutes and the mixer was b ack in working order
I ordered a speed control plate and followed the online instruction to install and adjust speed. Worked great
★★★★★
★★★★★
Shawn T - January 23, 2021
Verified Purchase
Straight forward repair
The part I purchased was compatible with my Kitchenaid stand mixer. I followed an instruction video and the repair took less than an hour. My mixer is back in action. Thanks
★★★★★
★★★★★
Cheryl M - May 14, 2021
Verified Purchase
Great service!
Part was here faster than expected. Mixer works great!
★★★★★
★★★★★
Rex H - January 24, 2018
Verified Purchase
easy repair
runs like new
★★★★★
★★★★★
NINA * - November 14, 2018
Verified Purchase
Easy repair!
I received the part in a short time and the repair was very easy.
★★★★★
★★★★★
Jim T - January 23, 2019
Verified Purchase
worked as expected
repair went well and mixer now works fine.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.4 / 5.0, 14 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Mixer ran way too fast at slow speeds.
‘Can’t remember well enough to describe accurately. Removed one screw to remove rear cover. Removed two screws to remove bright-metal band - probably not necessary but it did yield a bit more working space. IIRC, three screws and removing wires from spade-connectors was sufficient to remove the speed control plate. Remove one more screw
... Read moreto remove phase control board (probably unnecessary). I took close-up pictures with my iPhone first to assure wires would get replaced on the proper lugs (only to discover the wiring diagram later). Adjusting the control plate to meet the speed criteria in the instructions was very easy. It did serve to remind me that I probably didn’t need either of the new parts; readjusting the old speed control plate would probably have done it. But I appreciate the POM brought on by the new parts.
It’s an incredible pleasure to work on something so well-made as this old Kitchen-Aid mixer. I just enjoyed handling it! Having achieved a proper repair was rather satisfying too. I just loved the entire experience!
The mixer was given to my wife. Sometimes it would work or not.
When I took the back cover off I found two parts that "could" be the problem. The speed control plate was cracked which explained the spotty working. I ordered both parts and installed them very easily. The parts fit perfectly and resulted in the mixer working perfectly. I can't say enough about the excellent parts. They were perfe
... Read morect.
Read less
James from SAINT PAUL, MN
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The speed linkage was broken inside the mixer.
Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thank
... Read mores for having our parts and guiding us with a diagram of the unit. Very helpful.
Replaced the speed control plate and phase control board and works well. Pay attention to speed control board spring and adjustment lever when reassembling.
Pulled off end cover. Used the how-to video's to show me how to remove the (3) components (watch out when it comes to removing the spring). Removed all (3) components (one issue was the black cardboard seal, which because of its age broke. Hindsight tells me that I should have purchased a replacement seal along with the (3) new parts.
... Read morer /> Fixed the broken part of the seal with scotch tape). Installed all new parts with the help of the video's and put the cover back on. Even with the new parts, the mixer would not run. Come to find out, after I took it to an appliance repair person, that someone had pulled both brushes and put them back in improperly. I could not find a how-to video that showed me how to de-install/re-install the brushes properly. I assume that was because new brushes were no longer available for purchase. At any rate, when the brushes were put in properly, everything worked. The repair person also adjusted the (2) screws on the speed control plate so that when you change the speeds via the lever, it all works properly. I didn't find a how-to video covering those adjustments either.
SPEED WENT CRAZY, VERY VERY FAST. NO CONTROL AT ALL EXCEPT OFF
INSTALLED PHASE CONTROL BOARD AND SPEED CONTROL PLATE, BOTH AT SAME TIME Your DYI video was helpful, especially holding the spring with a cloth. Also good for fine tuning to get the speed exact
Watched a YouTube video to disassemble,from there went smoothly. One small piece of advice,take pictures with your smart phone during the process. Makes remembering easier.
BOARD-PHAS POINTS WORN AWAY AND 1 BRUSH STUCK AGAINST COIL
Took out stuck brush assy cleaned it and the coil and reinstalled it. Googled internet to see how to best remove and replace Board-Phase as no instructions came with parts. Actual work replacing parts took only a few minutes. The main work was tearing down the working head to get to the parts and putting it back together. Also had
... Read more to google how to adjust speed control plate to the correct speed. It helps to have patience and instructions.
use your phones to take pic of how the wiring is to be reconnected, take pleanty from all angles
repair is farly simple just take your time, First attempted i didnt replace the speed covernor looked ok but had problems getting slow end to work properly decided to go ahead and install since i purchased it also and walia took care of the cogging problem. Good Luck
Ask our experts a question about this part and we'll get back to you as soon as possible!
16 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cindy
November 15, 2018
My stir switch position does not work. Will this part correct the problem?
For model number K5SS
Hello Cindy, Thank you for the question. The Speed Control Plate controls the speed settings for the mixer. If you only have one speed or if some speed settings are not working, this part will fix the issue. Hope this helps, good luck with this repair!
11 people found this helpful.
Was this helpful?
Thank you for voting!
Phil
April 22, 2019
My mixer won’t stay in the off position. I have to hold it in the off position when i plug it in, then when i let go, it pops into at least second or third. It will function at all speeds, but i have to hold it in position if i want to use a lower speed. Will this part fix the problem?
For model number KSM95GR
Hi Phil, thank you for your question. You will likely need to replace this part or the speed lever itself. I hope that helps. Good luck with your repair.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Kathleen
November 20, 2018
I only have high speed. Does this part fix my problem?
For model number KSM75
Hello Kathleen, Thank you for the question. If the appliance only works on one speed, it is recommended the Speed Control Plate, PS11748567 and is the most common issue. It is also suggested to check the Speed Governor, PartSelect Number PS11753017 and the Phase Control Board, PartSelect Number PS11752886. Hope this helps, good luck with this repair!
Hello Terry and thank you for writing.
It certainly sounds like it could be a faulty speed control assembly PS11748567, you should check for signs of damage, and replace if necessary, also check the power cord for damage just in case. We hope this helps. Please contact us anytime if you require further assistance.
My artisan mixer turns on right away when i plug it in and only has one speed. When i move the speed control to a higher speed or off or on it just stays at the same speed. In order to shut it off i have to i plug it. Please let me know what i need to fit this machine. It’s only a year old. Thank you
For model number ksm150psmc
Hi Mark,
Thank you for your question. If you are unable to adjust the speed on your mixer, there are some parts that you will need to check to see which one is causing the issue. You will need to check the speed governor, the speed control plate and the speed control lever. We hope this helps! Good luck with the repair!
Our mixer stripped the worm gear under load and I replaced it. Now the mixer has much less mixing power when kneading. Something else worn out? Thanks for the help.
For model number K5SS
Hello Joe, thank you for your inquiry. According to our research, the issue is most probably with the speed control plate assembly, part number PS11748567. It controls the speed of the stand mixer motor. You may need to replace it to fix the issue. Glad to be of help!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Cindy
December 11, 2018
Our mixer does not hold a constant speed at low and med speeds. It is variable. What part controls this aspect of the mixer.
For model number K45SS
Hello Cindy, Thank you for the question. It sounds like the Speed Control Plate, PartSelect Number PS11748567 is defective and may need to be replaced. Hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bt
January 4, 2019
What is the warranty for this replacement part?
For model number Ksm150ps
Hello, Thank you for the question. All of the parts we sell have a 1 year warranty. Hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Maria
May 23, 2019
Does this speed control plate with the specifications below fit KitchenAid artisan model no. Ksm150pspk?Partselect number ps11748567
manufacturer part number wpw10119326
manufactured by Whirlpool
For model number Kitchenaid Artisan Model No. KSM150PSPK
Hello Maria, thank you for inquiring. Yes, this Speed Control Plate is the replacement for your model.
1 person found this helpful.
Was this helpful?
Thank you for voting!
V
May 28, 2019
Where is the gear part origin? In which country do you ship?
For model number 5K5SSWH
Hello, Thank you for the question. The Speed control is in the hosing. You just need to remove the back plate to access the control. We have warehouses throughout the US we ship from. Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
