Part Location Diagram of WPW10330804 Whirlpool Speed Governor
See part 35 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Speed Governor WPW10330804

★★★★★
★★★★★
1 Review

Rated by 7 customers 

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 19.89
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11753017
Manufacturer Part Number WPW10330804
Manufactured by Whirlpool
Product Description

Speed Governor Specifications

This speed governor, or clutch, can typically be found in your tilt-head or bowl-lift mixers beside the control plate. It is one of the three parts that work together to regulate and control the mixing speed. If you notice speed fluctuations or unresponsiveness to adjustments, the speed governor may be malfunctioning. To replace it, consult your user manual for instructions. Start by disconnecting the mixer from its power source and removing the beater and bowl. Take off the rear cover and unscrew the mounting screws from the trim to remove it. Disconnect the wires on the control plate and pry the end seal from the appliance. Remove the fasteners on the control plate to access the governor, which can be wiggled off the shaft using pliers. Please be aware that this OEM part is sold individually.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Mixer, Range Hood, Washer.
This part works with the following products:
KitchenAid, Whirlpool, Kenmore.
Part# WPW10330804 replaces these:
AP6019708, 17830, 4159675, W10330804
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 3.2 / 5.0, 7 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
Mixer would not turn on
Pulled off end cover. Used the how-to video's to show me how to remove the (3) components (watch out when it comes to removing the spring). Removed all (3) components (one issue was the black cardboard seal, which because of its age broke. Hindsight tells me that I should have purchased a replacement seal along with the (3) new parts.
Other Parts Used:
Speed Governor Phase Control Board Speed Control Plate
  • Tom from MARTINEZ, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Only worked on high speed
Followed the video on your website and it was super simple!
Other Parts Used:
BOARD-PHAS Speed Governor Phase Control Board Speed Control Plate
  • Barry S. from OLIVE BRANCH, MS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
use your phones to take pic of how the wiring is to be reconnected, take pleanty from all angles
repair is farly simple just take your time, First attempted i didnt replace the speed covernor looked ok but had problems getting slow end to work properly decided to go ahead and install since i purchased it also and walia took care of the cogging problem. Good Luck
Other Parts Used:
Speed Governor Phase Control Board Speed Control Plate
  • Douglas from FREEPORT, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer would only run Full Fast. Could not determine cause or fault.
1. Removed the mixer back plate Cover. 2. Removed the Speed Control Plate and retained spring, wires and ground wire. 3. Removed the old Speed Control Plate screws. Noted Control Plate pitted contact. 4. Removed old Triac Phase Control Board. 5. Removed old Governor. 6. Installed new Governor. 7. Installed new Phase Control Board. 8. Installed new Speed Control Plate and retaining spring. 9. Reattached Speed Control Plate wires. 10. Adjusted Speed Control Plate Screws and set mixer speeds from Stir to maximum settings. 11. Replaced Motor Brushes on left and right side of mixer. 12. Reinstalled mixer back plate cover.
Other Parts Used:
Motor Brush Speed Governor Phase Control Board Speed Control Plate
  • E.F. from HUNTINGTN BCH, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor did not turn on.
I removed the excess of grease to clear all parts. Then I installed new mechanical parts. Finally, I installed all electrical parts. I followed a logical sequence of removing and installing steps. Tip: Never remove parts without a logical order of sequence.
Other Parts Used:
Motor Brush Speed Governor Phase Control Board Speed Control Plate
  • Gonzalo from HAINES CITY, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer only had 2 speeds with the smell of electrical burning.
This mixer was given to me 8-10 yrs ago with only 2 speeds (cant believe i waited this long to fix it). Repair went good, wasn't sure what i should replace so i replaced Control board, control plate, governor, grease in the gears and the transmission gasket. I first took any and ALL measurements for any screws on the control plate, this will help when you set your mixer speeds when its all back together. When installing the new governor i used a 10mm socket and a mallet to seat it all the way till it stops on the set pin. installed the new control board, with thermal grease on the back of the plate(very important). Didn't need to replace the grease in the gears, but i figured since i was in there id replace it. (No smells and all gears work) I used it to ground 5lbs of elk into burger (speed 4) after repairs and it worked great. Still have about 15lbs left to do and itll do it with out braking a sweat. Maybe i should open up a repair shop to fix these suckers...lol its that easy. What really helped with the repairs is the youtube video from Partselect. Second to none with a step by step on how to replace and repair just about anything on your mixer. Good deal, if i need to replace anything else i know where to go! Thanks
Other Parts Used:
Speed Governor Phase Control Board Speed Control Plate Stand Mixer Gear Grease Transmission Case Gasket
  • Michael from MONTROSE, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
15 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Corroded speed control plate ( full of flour). Had used the mixer for grinding deer meat and lost the slow speed. Flour would fly up in my wife's face.
I just thought there had to be a way to replace a component to correct the speed problem. I've never worked on a mixer before, so I thought it would be a challenge. Actually the repair was fairly easy. Make sure the unit is unplugged from AC. I removed the back motor cover with one screw and removed the end seal. I compared the parts on the mixer with the diagram provided at the Part Select website. I then ordered the parts. When the parts arrived 3 days later, I removed the Speed Control Plate ( 3 screws) and Phase Control Bd (1 screw) as one Assy. Removed the old Governor and slipped on the new one. Assy the new Speed Control Plate and Phase Control Bd comparing wiring and screwed them back to the unit. Removed the two motor bushes by unscrewing the side black motor brush holders and inserting the new brushes. I tried powering motor and nothing happened. I thought, great, now what did I do? I found out that you must make sure the brushes actually touch the armature otherwise the motor doesn't run. The gears are worn from grinding to much deer meat and my wife says no more. I've ordered new gears and looks like that job, too, will be easy to repair. Adding these parts is alot cheaper than buying a new unit and it will run like new. Not bad for over 10 years of usage.
Other Parts Used:
Motor Brush Speed Governor Phase Control Board Speed Control Plate End Seal
  • Kenneth from Cowden, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

7 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike.Avad
January 26, 2018
The mixer seem to run to fast just on the stir senting? Why
For model number K45SS
PartSelect logo
Hello Mike, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: speed control plate, speed governor, the phase control board, and make sure the speed control lever and speed link are tightened and clear of debris. You can test the other parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Rosario
October 2, 2019
My kitchen aid mixer broke down while i was doing a dough. It suddenly just stopped. The motor is working but the beaters don't turn. I brought it to a service center and recommended to replace the following: Governor assembly, gear worm, and control plate. Can you please send me the exact specifications for these parts for model k5ss. Would these parts be available to be purchased in the usa? How many days is shipping time from ordering? Delivery location would be in st. Pete, florida. Could you also send me details of ordering ? Thank you so much!
For model number K5SS
PartSelect logo
Hello Rosario, thank you for your question .The governor is PartSelect Number: PS11753017, the worm gear is PartSelect Number: PS11748374 and the speed control plate is PartSelect Number: PS11748567. Please enter the part number into the site for current price and availability. We do ship within the US and could help place the order for you and provide more information if you'd like to cal to place the order! Good luck with your repair!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Dean
December 19, 2018
Mixer is noisier than normal and 8 and 10 speed setting has no noticable change in rpm or sound. I will order the govenor, plate and phase board.
For model number K5SS
PartSelect logo
Hello Dean, thank you for your question. Yes, we would recommend replacing both the PartSelect Number: PS11753017 and PartSelect Number: PS11748567. While you're replacing those parts, check the worm gears and other gears in the unit and make sure they are well greased. I hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Ann
November 26, 2018
I have no 1st/ low speed, on 2nd speed it just sounds like grinding but won't spin. If bowl is empty it will spin on lower gears, if fill it has to be on high speed not will quit spinning after about 5-10 minutes of use? Just want to see which all parts to order? Thanks
For model number KSM150PSBY
PartSelect logo
Hi Ann, Thank you for your question. If you are having an issue with the speed of the mixer, there are some parts that you will need to check to see which ones are causing the issue. You will need to check the speed governor, speed control plate and the speed control lever. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Matthew
October 29, 2019
The motor on my mixer is intermittent, like its losing contact intermittently. I replaced the speed control plate but it never would adjust to run smooth. Does it need brushes?
For model number k45ss
PartSelect logo
Hello Matthew, Thank you for the question. Yes, defective or worn brushes can cause this issue. If you remove the brushes you should be able to tell if they need to be replaced. Hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
Matthew
November 9, 2019
Ok, so i replaced the speed control, the brushes, but it still runs rough and noisy. Like the contactor springy things on the back arent keeping contact. Speed is mostly constant at higher speeds but lower speeds its intermittent. Governor? Motor? Gear? Thanks again.
For model number k45ss
PartSelect logo
Hello Matthew, thank you for your question. It sounds like a speed governor issue. We would recommend replacing that part next. I hope this helps.

Was this helpful?
Thank you for voting!
Steve
December 2, 2022
I replaced the speed control module and the mixer speeds are fast on stir setting. No adjustments on module help on adjusting speeds on any setting. Now what?
For model number KSM90
PartSelect logo
Hello Steve, thank you for reaching out. According to our research, we would suggest replacing the Phase Control Board, part number PS11752886. The phase control board helps control the speeds. If that does not help, we would suggest checking the Speed Governor, part number PS11753017. If you require assistance placing an order, please contact customer service. We hope that helps!

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11753017
Manufacturer Part Number: WPW10330804
Brand
Model Number
Description
Kenmore
1106102300
Washer
Kenmore
1106112600
Washer
Kenmore
1106201300
Washer
Kenmore
1106202300
Washer
Kenmore
1106202310
Washer
Kenmore
1106301200
Washer
Kenmore
1106301201
Washer
Kenmore
1106302300
Washer
Kenmore
1106302301
Washer
Kenmore
1106401200
Washer
Kenmore
1106402300
Washer
KitchenAid
3K45SS
Mixer
KitchenAid
3K5SS
Mixer
Whirlpool
3KSM150PSTAQ0
Mixer
Whirlpool
3KSM150PSTBM0
Mixer - Stand Mixer
KitchenAid
3KSM150PSTBW0
Mixer - MIXER
KitchenAid
3KSM150PSTCB0
Mixer - MIXER
KitchenAid
3KSM150PSTCL0
Mixer - MIXER
KitchenAid
3KSM150PSTCU0
Mixer - MIXER
Whirlpool
3KSM150PSTDR0
Mixer
KitchenAid
3KSM150PSTER0
Mixer - MIXER
KitchenAid
3KSM150PSTGA0
Mixer - MIXER
Whirlpool
3KSM150PSTIC0
Whirlpool
3KSM150PSTLR0
Mixer
Whirlpool
3KSM150PSTMH0
Mixer - Stand Mixer
KitchenAid
3KSM150PSTMY0
Mixer - MIXER
KitchenAid
3KSM150PSTOB0
Mixer - MIXER
Whirlpool
3KSM150PSTPA0
Mixer - Stand Mixer
Whirlpool
3KSM150PSTPK0
KitchenAid
3KSM150PSTTG0
Mixer - MIXER
Customer Service Representative

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service