Models > YMH7155XMB1 > Instructions

YMH7155XMB1 Whirlpool Microwave - Instructions

All Instructions for the YMH7155XMB1
61 - 75 of 235
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Handle broke off
-leave door attached to microwave.

-remove three phillps screws from end of door next to handle.

-use two flathead screw drivers to pry apart the outside cover and unsnap the two sections of the door. Start in the top middle.

-use phillips screw driver to remove two screws holding handle on.

--handle has an up and down side, attach longer side to the top of the door.

-snap two door pieces back together.
Parts Used:
Door Handle
  • Randall from CHAPEL HILL, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not heating up
Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.
Parts Used:
DIODE
  • Michael from GLENDALE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lights bulbs burned out
Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.
Parts Used:
Light Bulb - 40W
  • Kat from Hudson, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plastic screw brackets had broken on the original model.
Removed the old vent grill by removing the two screws and put in the new one.
Parts Used:
Vent Grille - Black
  • James from Battle Ground, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken plastic tabs caused grille to fall off
Very simple, just removed the screws and plates from the top of the microwave and reused the screws to secure the new piece.
Parts Used:
Vent Grille
  • Keith from Mesa, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Vent grille was broken
Removed the two screws hlolding the old vent in place. Discarded the old vent. Snapped the new vent in place and attached with the two screws previously removed.
Parts Used:
Vent Grille
  • Eugene from Tampa, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bought microwave at Garage sale, but with no mount bracket
I was able to buy the mounting bracket for a very cheap price and was able to instill it in my kitchen with ease.
Thank you
Parts Used:
Mounting Plate
  • Jesus from Lincoln, NE
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
9 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
glass turntable broke in half, ring turn needed replaced
I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next
Parts Used:
RING-TURN
  • Gail from Cincinnati, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken vent Grille (plastic tabs snapped)
All you have to do is unscrew the clamps, remove the broken plastic pieces of tabs, fit the new grille into the slots on the bottom and put the two screws through the clamps at the top.
Parts Used:
Vent Grille
  • Aaron from Trumbull, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb burned-out
screwed in new bulb
Parts Used:
Light Bulb - 40W
  • Pablo from Burlingame, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
13 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hood light wont work
Turned power off. Removed all the screws from bottom removed socket and replaced
Parts Used:
Light Bulb Socket and Housing
  • Brandon from Vancouver, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
9 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken glass tray
Washed the glass tray and put in the microwave oven. Easy..
Parts Used:
Glass Cooking Tray
  • Mary from Ocala, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb burnt out .
Turn off power supply at breaker . Replace old bulb with new bulb .
Parts Used:
Light Bulb - 40W
  • DAN from CARPENTERSVLE, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Range light bulbs were burned out
We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Parts Used:
Light Bulb - 40W
  • Barbara from MERIDIAN, ID
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out bulb
Husband replaced the bulb
Parts Used:
Light Bulb - 40W
  • Theresa from OVERLAND PARK, KS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YMH7155XMB1
61 - 75 of 235
Back to Top