Models > WWBD2400HW9B > Instructions

WWBD2400HW9B Westinghouse Dishwasher - Instructions

All Instructions for the WWBD2400HW9B
106 - 120 of 205
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old gasket melted.
Watched installation video and followed directions. All went smoothly.
Parts Used:
Dishwasher Tub Gasket - Gray
  • Al from WOODBURY, MN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Some of the silverware slip thru the silverware holder. During the drying cycle the exposed silverware was to close to the arm and melted an area of the arm which caused water to seep out onto the kitchen floor.
To remove the spray arm just squeeze the sides pull up and replace the new lower spray arm in it's place. Just push down.
Parts Used:
SPRAY ARM
  • Gloria from Washington, DC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking water under door
Well, I actually was unable to make a repair.
Initially I inspected the door gasket and it appeared to be hardened, so i thought a new gasket would fix the problem.
I ordered new gaskets and went back to make the repair. Well, as I was removing the door gasket, I noticed the door bottom had been damaged and was deformed beyond repair, which was the real reason it was leaking.,
Parts Used:
Dishwasher Door Bottom Seal Dishwasher Tub Gasket - Gray
  • John from PEABODY, MA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Brass nut split down its side , why ???????
Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.
Parts Used:
Heating Element Brass Nut
  • Bill from PORT ORCHARD, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spray arm had come off and melted on the heat coil
New piece snapped right on
Parts Used:
SPRAY ARM
  • Bonnie from SPOKANE VLY, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher Sprang a Huge Leak
I pulled out the dishwasher and found the inlet tubing had a tear in the accordion part of the tube. I searched online for the model number and was directed to PartSelect. I ordered the inlet tubing, and it only took a few days to get to me. I then watched the video and was able to install the new tubing.

PartSelect is a life saver and I saved lots of money by not having to call a repairman.
Parts Used:
Dishwasher Water Inlet Tubing
  • Rita from MEDANALES, NM
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spray arm melted and needed to be replaced.
The old part easily snapped off and the new part was snapped into place. No tools were needed. Very easy. Saved quite a bit by doing it myself instead of calling a repairman.
Parts Used:
SPRAY ARM
  • Tomasina from WEBSTER, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spray Arm melted easy replacement
Popped it in and done
Parts Used:
SPRAY ARM
  • Amanda from HAYESVILLE, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The heating element (ring) showed signs of wear
I followed the steps on YouTube.
Parts Used:
Heating Element
  • Leonard from N ROYALTON, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lower spray arm came off and melted on the header coil
took old one off by hand, snaped the new one in place by hand
Parts Used:
SPRAY ARM
  • steve from PT CHARLOTTE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing part
Just pushed it onto the rod that held the old one
Parts Used:
WHEEL & BUSHING ASS
  • Michael from STEWARTSVILLE, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My heating element was cracked
Remover the cracked heating element with the new heating element.
Parts Used:
Heating Element
  • Jimmy from COMSTOCK PARK, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser failed to operate
Uncomplicated repair. Remove door, remove old dispenser, install new dispenser.
Parts Used:
Detergent Dispenser
  • GENE from BRONX, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two of the tub wheels cracked and broke off.
Unscrewed the old ones, new ones come with screw built in and recrewed the new ones in. So easy.
Parts Used:
ROLLER ASSEMBLY
  • Sharon from HAMPTON, NH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom Basket Cage Broken Rack &, Spray Arm Falls Off
1. Engage B.R.A.I.N. :
B: Break open the Box. You know you'll never get it back in
R: Read Instructions: It's not more packing material.
A: Assemble New One: Put it together just like the old one
I: Ignore Instruction: Seriously, sharp edges will cut me?
N Never listen to the wife Or at least pretend to be listening
Parts Used:
Lower Dishrack Assembly SPRAY ARM
  • MICHAEL from PHILADELPHIA, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WWBD2400HW9B
106 - 120 of 205
Back to Top