SE1000 Maytag - Instructions

Tilted the washing machine back at 45 degree angle. Removed three screws from the underside of machine. Slipped belt off pump. Lessened two hose clamps and removed hoses.
Lifted old pump out. Dropped new pump in place.
Screwed in the 3 screws. Slipped on the belt.
Attached two hoses. Tightened hose clamps.
Set washing machine upright.

No more leak.
My problem was I could not prove the pump was the source, but after switching it out I have had no problems (good enough).

That would take forever to write in everything you have to do, but I did go to a website that had the steps you must do to complete the repair. You can google tub seal kit and mounting stem and the brand of your appliance and i'm sure you will come across the steps to complete the repair. I would advise you to first order a spanner wrench it makes the job much easier and you really can't complete the job without it. So do that first and then take the machine apart if you suspect it's a tub seal leak and then order your parts. if i had a spanner wrench available to me from the beginning it would have gone much smoother from the start.

By doing the work yourself, not only gives you the good feeling you did it yourself and works just like it was when it was new and to know there's part's you can still get from part places like these! Like I say to my wife ( if they meaning a repair shop can do so can't I ). Course changing a motor in a car that's a different story, I'll let someone else to do that. To do the repair I took off the front cover of the washer exposing the tub, motor and other things. But the very first thing I did is unplug the power ( I hate the bad storys that if I only turned off the power ? ) then I took off the cover over the motor and changed the switch. And all in reverse. And plug power back in. Started up just fine.

popped out old female clasp on dryer itself with screwdriver, undid 2 screws on dryer door and door handle with phillips screwdriver, popped in new male clasp part, put door knob back on and put the two screws back in door and it was all set to go. Less than 15 minutes to do. Better than new and wife is happy. No more duct tape holding door closed now.

Simply disconnected 2 screws that hold on a metal cover plate for your arm to fit in.
Then disconnected 4 screws that hold the syphon in place, remove the syphon elbow and replace it with the new one, insert the four screws again and tighten making sure your arm is holding the elbow from the inside of the machine through the access hole. Then install access panel with the screws, do a test run with the machine pulled out to see if there are any leaks. Done.

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

I opened the front of the washer by removing the 2 screws on the bottom front of the washer, then swinging the front upward until it was clear of the hangers at the top. The hose sits right in front. It was cracked where it attaches to the tub. I loosened the hose clamps at the tub & the pump with a nutwrench & removed the old hose. I slid the clamps onto the new hose & put the hose on to the tub & pump. I tightened the clamps, reinstalled the front & was finished.

Using the instructions accompanying the belt I bought from you,I removed the casing an front support for the drum. I then tried to follow the instructions to install the new belt from the front and found it to be absolutely impossible.I saw that there is a removeable plate on the lower right corner of the back that,if removed, would expose the motor and idler pulleys that are the object of the installation so I removed it and,without much difficulty, installed the belt. One problem in doing so involved the belt's tendency to slide into the groove in the drum when manipulating it onto the pulley set so I enlisted the aid of my wife to hold it in place from the front while I successfully and rather easily did so.

Sans manual, I turned to the web to find out how to open up the dryer. Maytag uses two Phillips screws on the bottom front panel. Once removed, the front pulls out at the bottom and slides free from the top. Caution, wires on the left side of the front panel prevent total detachment from the dryer. A 1/4 hex screwdriver was used to remove the cover to the blower housing. Once the cover is unbolted attached wires prevent its complete removal and can be set clear of the blower housing. Pliers were used to remove a pinch clamp from the squirrel cage fan (blower assembly) and snap ring pliers were needed to remove the retaining snap ring. The fan was easily removed from the motor's rotor. The loose fan caused damage to the blower housing which I believe was the source of the original rattle. Once the fan had been removed, the housing was removed by using a 5/16 socket on the end of an extension. The replace parts were installed in reverse order and fit perfectly. Other work included the replacement of the drive belt for the drum. PartSelect was chosen because it had the parts in stock and could be shipped overnight.

First I turned off both the hot and cold water supply to the washing machine. I then turned on the washing machine causing it to attempt to fill the tub and thereby releasing any pressure remaining in the watter lines. I then canceled the wash cycle and unplugged the power line to both the washer and dryer. I removed the water lines from the back of the washer, unscrewed the bolt securing the solinoid mounting plated with a pair of slip joint pliers. I slid the plate out of the back of the washer and removed the outlet line from the solenoid valve by unscrewing the clamp with a screwdriver. I removed the old solenoid valve from the mounting plate by unscrewing the mounting screws with a screwdriver. I reassembled the washing machine in the reverse process.

Took off face of dryer (two lower screws below door in front) and then removed the drum which gave me access to the idler arm and idler pully. Vaccumed the interior to remove dust and lint. Replaced idler arm and idler pulley assembly. Replace old belt as drum was reinstalled. Opened rear access panel to complete final routing of the new belt over idler pulley and drive motor. Turned the machine on to check repairs and function. Closed rear access door. Pushed dryer back into place and re-leveled machine.

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

It was very easy to access the parts that needed to be replaced (blower wheel, belt, and glides).
1. Unplug the dryer power cord.
2. Removed the two screws at the bottom of the front dryer panel. Pull the bottom of the panel forward, which frees the retaining clips at the top of the panel.
3. Disconnect the two wires from the back of the panel, and remove the panel. The drum will be resting on the motor/blower hosuing.
4. Slide the belt off of the back of the tumbler, and remove the tumbler (have to angle it a bit, to clear the frame) and the belt.
5. Remove the thermostat cover (piece of angled sheet metal, in front of the blower unit).
6. Remove the screws from the blower housing, and lay it forward, to expose the blower wheel.
7. Remove the snap ring, and then the retaining ring from the blower wheel. Remove the old wheel.
8. Install the new wheel, then the retaining ring, and then the snap ring. Reattach the cover to the blower assembly.
9. Reattach the thermostat cover.
10. On the tumbler, drill out the rivets for each of the glides, and remove all glide parts. Install new glides.

This is a good time to complete any general cleaning inside the dryer cabinet, especially in the area of the motor. Since there is limited access to the motor itself, might help to use the blower function of a shopvac to blow out that dust.
Vacuum out all lint from around the felt drum seals.

11. Loop the new belt over the tumbler, and install the tumbler (the glides go towards the front of the dryer). Note: to keep the belt from falling off, I taped it to the drum with two pieces of painters tape..the blue tape that comes back off easily.
12. On the back of the dryer, remove the access panel, and complete installation of the belt to the idler pulley.
13. If you taped the belt to the drum....don't forget to remove the tape now. Reinstall front panel to dryer.

This was my first experience working with snap ring retaining rings. Even with snap ring pliers, they are difficult to remove without stretching them out. Be sure to order a new one with your blower wheel.

Also my first experience using a pop rivet gun ( to install the new glides). Found a rivet gun at Lowes for $9.99. Worked okay, and all rivets set properly. Good thing, because you don't get any extras with the glide kits.

After replacing the parts, and starting up the dryer, all of the clunking/squelling/rumbling noises were gone. There was a noticable smell while the new glides got broken in...smelled a bit like melting rubber. However, after a couple of drying cyles, the odor was gone.

For the most part, I followed the excellent repair advice already available on this site for installing these parts. Especially useful was the caution that the threaded pieces had "left hand" threads and to loosen them they had to be turned in a "CLOCK WISE" direction. My washer is 9 years old and due to calcium deposits on the threads, I did have some trouble with loosening the large retaining nut. I first soaked the nut for a few hours with a rag soaked with white vinegar. This removed some of the calcium but I still was unable to undo the nut. Finally, I soaked the nut overnight with penetrating oil and WD-40. The next morning I was able to loosen it using a drift punch and medium sized ball peen hammer. I only had one difficulty. Maybe it wasn't necessary to do so, but I wanted the rubber boot seal to be seated pretty close to the surface of the inner basket. This turned out to require more downward force than I would have expected even though I installed it dry, without use of any type of lubricant or soapy solution. Now, two weeks worth of washing and not a drop of water seen underneath the washer.

Before anything, I unplugged the dryer and tipped it over on its front. Then I removed the lower access panel and saw that the belt was broken. I removed the belt. I replaced the panel and put the dryer upright. When I ordered the belt off this site, I used one of the repair stories. With a phillips-head screwdriver, I removed the two screws below the door on the front panel. The panel is held in place by two clips at the top. Gently pull the cover off, since there are also two door-open sensor wires connected to the front panel. I removed the hex nuts holding the tumbler in place. When I started to put the belt on, and was having a bit of trouble, my neice pointed out the diagram on the bag the belt was in. From then on it was a piece of cake. I got the belt in place, replaced the tumbler and front panel, and plugged it in. Good as new!