Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Inner glass pane broke during self-cleaning operation
I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.
Bottom oven door handle broke when someone tried to open door too soon following self-cleaning cycle.
We removed the door from the hinges by sliding it up. Then we removed all the screws holding the door together. We had to remove the screw securing the trim. Next we removed the screws inside the trim holding the old handle. We replaced the handle and trim and screws in reverse order. Finally, we re-attached the door by sliding it onto the hinges.
The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!
Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.
I was pleased with how the job went. It took longer than expected because I am not really a "do it yourselfer", but I studied the door and reread how others managed the repair several times. There were more screws than mentioned here. Someone said 10 screws but there were 12. In the end I was pleased and surprised how simple the job was, but recommend others read carefully what others have written. I didn't but learned one must.
Shattered inside glass when attempted to self-clean
Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.
Crazy codes and not heating the oven properly at desired temp settings
1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!
Just removed the shield (2 wing nuts) than the burner (1 Screw). THe back needs to be removed to unplug the igniter. I than reversed the process until I got to the plug and found that I had 2 male ends. I than had to remove everything and go back to square one until I find the part with the correct end (which should be Female) I'd check this before getting too deep into the repair.
• Removed the oven door (pulled right off old hinges) • Removed two screws • Removed broken hinge • Placed new hinge in place • Replaced screws • Replaced oven door.
Bought new hinges as that was the obvious problem. Below is the removal, installation process for new hinges. Turns out in my case there was nothing wrong with the hinges. Problem was still there after installing new ones. I found that the metal in the door that butted against the hinges was fatigued causing looseness. I ended up compressing the metal back into shape with a hammer. Problem solved but money wasted on hinges. If you replace hinges. Here is what I did. 1. Open door slightly to where it stops in broiler position. 2. Remove the door by pulling up. 3. Remove two screws in front of hinges that hold them in. 4. Pull range out a few inches for access the remove the side fillers that trim out the stove. 5. Reach in from the side and work hinges out. 5. Pop in new hinges and reattach the 2 front holding screws and the side trim screws. You are done.
I took the door off and removed five phillip screws from the old bottom support and removed it. I took the opportunity to clean the glass on the front and back before placing it back on. It simply fits into two keepers at top and is held on by the new support at the bottom. I replaced the five screws and put the door back on. It is a simple job that only takes a few minutes.
Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.