MDE21PNAGW Maytag Dryer - Instructions

With the parts in hand, and after disconneting power and shutting off gas line, I again removed the door, front panel and front tumbler frame to expose the blower wheel. I discovered that the blower wheel was not damaged, but that compressed pieces of lint and other items where stuck to the wheel. I removed the pieces and vacuumed the the whole thing clean, tested it, and the sound stopped. Since I had the unit open, I replaced the front glides by drilling out the old rivets, removing the old glides and then riveting the new glides in place. A very simple procedure overall.

Make sure you keep track of where the different screws go and keep them inside something so you don't lose them. I also used my cell phone to photograph various areas and screws for later reference.

I removed and replaced all the problem pieces, and now she runs better then when I got her!

first, i removed two screws at the bottom of front panel. then lifted from the bottom removing it. next, removed drum surround and drum. next , removed right roller and roller shaft. then installed new shaft, slide roller back on shaft. next reinstalled drum, drum surround and front panel. Now so quiet you can hardly hear it run, also my sister says it drys much faster.

First thing to do. . . . Unplug the machine. After that, remove the top 2 screws from the cover from between the washing machine and the dryer and remove cover. Then remove the 2 screws from the top of the front dryer cabinet, pull front cover out slightly and gently let it lay forward. From this point, you can look in and see the drum rollers. Behind the rollers on the roller shaft is a 1/2" nut. Use a 1/2" gearwrench to remove the nut, and pull the shaft with roller attached out forward. Use snap ring pliers to remove snap ring, take off old roller with bushings, and replace with new. To re-install shaft with new roller, you will have to lift the drum slightly to give yourself enough room. Re-assemble the front of machine (note: be careful of the wiring on the control panel, as some connectors may have pulled loose. Make sure they are all connected before replacing front of machine). Plug machine in and test it out. While you have the machine open, use a good vacuum cleaner and remove the lint that you will find inside the machine. Depending on how old the machine is, you should find quite a bit.

Read the instructions included with the parts, removed the 2 screws on the front of the dryer. Removed a couple of wire connections and 4 screws that held the drum in place. Moved the drum enough to have access to the roller supports. I removed the nut from the back of the supports with a 1/2" wrench. Placed the new supports on the old support pins and reinstalled them. Put it all back together. Probably the most difficult task was getting the drive belt back on the drum correctly. I was done in just over 1 hour.

I had to remove the door first. Then the retaining brackets that hold the upper lid on. This also allowed removal of the front cover. After releasing the tension of the drum belt, I removed the drum and replaced the drum roller in suspect. Installation was reverse in order. Don't know why I waited so long to do such a simple job.

First I removed the two screws on the front panel that hold the element in place. I then pulled the element out about 3" and disconnected the two wires. Find out the roller broken. Place an order with Partselect from friend recommendation. Fast delivery, replace the broken roller, reverse the process and test the sound of the dryer. Very satisfied with the parts. Thanks!

After taking apart the machine (applianceaid.com has slideshows for most major appliances - very comforting and reassuring - highly recommended), I used a shop-vac to clean up all lint and dirt. After getting the retainer ring off the drum roller shaft (snap ring pliers highly recommended), I replaced the drum roller along with the glides which were completely worn through (rivet gun required). I reassembled the dryer to find that the drum wouldn't turn, so I placed another order for the other drum roller and replaced the belt too. Back in business.

Remove the door and front cover ,then the top flips up ,remove the front drum support then the drum,remove the snap ring and the pulley

Found out you shouldn't try to dry heavy hiking shoes in a dryer....it tends to break off plastic baffle.

The repair directions on PartSelct.com made this repair a piece of cake.
Just removed screws holding door and front of dryer.
With these removed it was a simple matter to detach top and get access to internal components.
Two hex screws held baffle in place.
Total repair took about 15 minutes, but while I was in there I cleaned out all the dust from inside of the dryer and heater unit.
I also reversed door to make it easier to transfer clothes from washer.
The instructions, detailed drawings and the quality of the part were all excellent.
They had replacement to me in 1 day.
Will definitely use PartSelect again.

Firts I had to take all the front parts off using a screwdriver and nutdriver then I loossen the belt to get the drum out then I had to use snapping ring pliers to remove the rollers and put the new ones in I cleaned the inside of the dryer then I put everything back in place. After all that I tested it and it worked really good it took me about an hour to do all that

Went on line and got a diagram of the dryer. Removed four screws around the door. Removed the door and then the front cover. The toughest part was removing the drum. Once I got that out of the way replacing the rollers was easy. Re installed the drum. The belt was a little tricky but worked. Then replaced the front of the dryer and the door. The dryer works fine now and no more noise. Pretty easy.

My son did the repair work. He took off the door and then carefully unhooked the belt and removed the drum. Replacement on the drum roller kit went smooth, and he then oiled the idler pulley while he was in there. I now have a "quiet dryer" once again!!! Had orderd the wrong part to begin with, but was very easy to return, receive my credit and get the "right" replacement part.
Great Service!!!!

Removed the door then removed front panel then removed 8 screws that held the drum in. At this point reached in and removed the snap ring on the wheels and replaced the washers and wheels. Then reassembled it.

repairmen said to buy a new dryer! or replace the motor! DO NOT EVEN THINK ABOUT IT!

It was the spring washer that was rubbing against the metal that was causing the very loud noise. The fiber washer that is used on the shaft on both sides of the roller had worn though and allowed the metal-metal contact. The fiber washer wore out! The fiber washers are very cheap!!!! in comparison to a motor or new dryer!


The drum rollers that support the rotating drum eventually wear out the fiber washer.
UNPLUG THE DRYER, DISCONNECT THE VENT
Remove the two screws on the lower front of the dryer panel, probably after you have tilted the unit backward. Remove the front panel by tilting out the bottom as there are two clips at the top. AFTER DOCUMENTING the CONNECTIONS - Disconnect the wires from the switch which is mounted on the front panel.
Carefully put the dryer on its back - be careful of the dryer vent to avoid damaging your floor or dryer vent!
Carefully pull the dryer drum up out of the dryer - as this is done the belt which moves the drum will fall away from the drum. I suggest before you remove the drum to eyeball the way the belt is tensioned and wrapped around the motor driveshaft, guard and tensioner. This will be the most difficult part of reassembling the machine. Some visual understand, maybe even pictures will help you later to get it installed correctly back into proper position... and it is NOT intuitive!
Once the drum is removed, the rollers are accessible. Rotate each and find the squeaker!
I recommend you replace the fiber washer on both, even though only one may be squeaking at this point (the other will be close to being worn out as well!).
I will not document the replacement of these parts as the assembly seems well documented elsewhere. I suggest you remain using the spring washer if there - as the after factory replacements do not seem to provide spring washers.
I would also suggest replacing the dryer drum belt, it is worn, after this many years, and putting in a new one will keep the dryer running for many more years. KNOWLEDGE IS POWER - USE IT