LFXS30726S (00) LG Refrigerator - Instructions

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Before you begin, I'd recommend unplugging the refrigerator. You have to slip the putty knife in around the edge of the dispenser panel and carefully release the tabs all the way around and the entire panel pulls straight out. There are three wiring harnesses to unplug. You'll have to remove several screws and release the tabs around the electronic panel and remove it from the main panel. It's a good idea to take note or even pictures of how the ice and water actuators are positioned on the panel, so you get them situated properly on the new panel. If the ice actuator is not fit correctly on a knob that sticks up it may dispense ice all the time (happened to me). After you transfer the actuators to the new panel and the ice and water dispensing levers, you can re-attach the electronic panel on the left side. make sure all of the wiring harnesses are plugged in and the wires situated out of the way, then re-install the panel by pushing it straight back in. Plug the refrigerator in and test it out.

For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours before you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.

easy repair. First step is you need to remove all food from bottom shelf and remove all three produce drawers. Then remove the meat drawer. You will need to lift the bottom self off the rail to remove. It is not heavy and does not need to be fully taken out of fridge - easier if you do but some what hard to get out.Unscrew the rail and unplug the old rail. Clean off the fridge - my fridge was gross behind the rail. Insert the rail into the fridge and then screw in the two screws. Place the bottom self back on the two rails and you are done.

Once I U tubed the the removal and replacement of the gaskets it was super easy. The right gasket change was easy without tools. The left gasket required me to remove the mullion first, which is why I used Utube.

Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary waste of time and labor.

Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.

Un-wrapped the basket......Installed with NO tools......

The Ice Maker from Part Select was complete. Plastic housing, Ice maker located at the top and ice cruncher/dispenser at the bottom.
Note: Both the ice maker and the dispenser wiring goes to a common connecter. It is not advisable to plan changing out only one of these.

Watched a couple of YouTube videos and then went at it

Opened the box. Removed wrapping. Washed the new part. Unloaded old basket. Removed old basket. Set in new basket. Loaded new basket. Closed the door. Even an 80 year old can do it!

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.

Removed the old one and replaced with the new.

Very Intuitive.
Removed ice cube holder.
Removed all visible screws or fasteners paying attention to size, length and location.
With wiring and connectors exposed, I disconnected those and was now ready to install new ice maker in reverse order.
Once reassembled it took approximately 2 hrs to start making ice.
I found part installation to be really quiet easy.

Removed the section of refrigerator that dispenses ice and water. Necessary to pry with object that does not scratch like plastic scraper. Then pull out and replace the switch Micro -- only has one Phillips screw holding switch. Replaced the dispenser and snapped on the New button assembly I broke and job was done. Works perfectly now..