LAT9416AAE Maytag Washer - Instructions

Once i figured out it would not drain i pulled the front panel off and pulled all the drain hoses off to be sure nothing was clogged there or in the pump itself. It was not so then i checked the drive belt and it was ok. Next i pulled off the drain pump and everything looked to be ok, it was not froze up and it would spin just fine. I got a screwdriver and held the splines inside the pump while trying to turn the pulley and thats when i found that the propeller was spinning on the shaft and under a load would only spin the shaft and not the propeller inside the pump. Got online ordered new pump and it works great now.

Removed the front - isolated problem to inlet valve when under pressure. Placed order with Parts Select. Removed inlet valve, three screws - swapped three wires and reattached hose, bolted back in place - done. Replaced belts while I was there, might as well, 21 year old machine - good thing I did, imminent failure on the drive belt.

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

First checked for clogs or loose/broken belt. Fixed loose belt and tested, not the problem. I then ordered the pump and hose that would not seal after uninstalling. Everything working fine. Very simple repair.

I watched the online video that was supplied when I ordered the part and it made all the difference in a successful repair. Thank you for having such a complete solution!

Unscrewed old one...screwed on new one. Needed to save the softener cup. Took 10 minutes.

Follow the instructions on the various video's. They were all very helpful. Removed all parts (have a small bucket ready). Also, be sure to order all hardware for drain pump. It does not come with any, and depending on the age of your washer, you will need new screws.

After troubleshooting the drain system and my plumbing, I read online that it could be the open door switch. Part select agreed and I ordered the part. Their handy troubleshooting guide was helpful. The part came a few days later, and I easily replaced it. Has been working for two weeks and running.

Replaced both belts, just like the video's on you tube. Pulled off the old one's, put the new one's on. Washer runs better then it has in years.

I took the front off by removing the two Phillips head screws at the bottom. I leaned the washer backwards and blocked the front up about 6 - 8 inches. Next I loosened the three screws that hold the pump on. Then remove the belt. Now it is time to get the hoses off by taking the clamps loose. Wiggle the hose and pull them off. You need a small bowel and towels to collect the water in the hoses. The final step is to take out the three screws that you already loosened that hold the pump on. The pump can now be lifted up and removed. Replace the pump with the new one and reverse the procedure.

No brainer. Simply followed the inclosed printed directions. Replaced both pump and drive belts. Didn't find it necessary to adjust belt tension.

I first thought I would buy a new washer, however, after seeing the complaints that purchasers were having with the new models, I decided to repair my old 'trusty' Maytag. I first watched the video that showed the replacement of the parts and followed the directions in the video. Since the washer was old I also cleaned all of the pullies to remove any debris and grease that had accumulated on them over the years. After replacing the pump and belts I ran the washer and it sounded like a new one! I saved myself over $600 by repairing my old washer rather than buying a new one. They don't make washers like they used to.

Pulled back cover plate off (one screw). Detached water inlet valve from plate (one screw). Slid hose clamp down hose to remove valve. Replaced valve (reverse procedure).

This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

Ordered new belts and install them in less than 15 minutes.