JDR8895BCB13 Jenn-Air Range - Instructions

Pull range out 6 inches. Open door to 45 degrees and pull up to remove door. Remove both side plates, two screws each side. Remove both hinges by loosening two small bolts on the front of range that connect to the hinges. Place new hinges in place. Bolt hinges using bolts you removed, replace side panels. Slide door on hinges and push back range.

PULLED THE POWER CORD!! Loosened a couple of screws holding the element to the rear oven wall, removed the electrical wires (red on left, yellow on right) attached to the baking element, removed old element, inserted new element and reattached the wires respectively thereto. One minor glitch did occur. The RED wire inadvertently slipped back through the hole into the insulation and was not retrievable. I removed the small metal plate housing the wires on the back bottom of the stove, pushed the red wire (plentiful length) back into the oven, reinstalled the plate, connected the red wire to the bake element, reconnected the power, element began to heat. Mission accomplished. One caution: Pay attention to the SHAPE of the failed element before ordering online or buying in person.

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control.

I pulled the range out, unplugged it and removed the back panel with a Phillips-head screwdriver. I then removed the two screws inside the oven that holds the element in place. I located the two wires on the back of the range attached to the element. I gently pulled off the wires using a pliers and then easily removed the burned out element. I put the ends of the replacement element into the respective holes, screwed them in and then plugged the wires back on at the back of the range. After replacing the back panel, I plugged the range back in. I turned the oven on with an oven thermometer inside, to test it out. I imagine I saved at least a couple of hundred dollars for the repair with this simple DIY, if not, the cost of a new double oven range!

not to offend anybody but what i learned on prior posts helped alot..
1. remove unit and unplug.
2. remove door by opening to 45 degree angle and lifting door face towards you.
3. remove back panel to unit.e.
4.unscrew burner element from back inside of oven.
5.gently pry clip off each off burner element from rear of unit. Pull gently towards you.
6.unscrew support from inside oven.
7. remove old element and just reverse directions to reinstall.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed oven door and rack. Removed two screws holding element. Disconnected wires to element. One of the wires slipped into the back wall of the oven. The range had to be removed from the counter and back panel removed to gain access to the element wires. Install new bake element in upper oven. Connect wires to element spade lugs. Install rear panel. Restore power at circuit breaker panel. Very important - aways disconnect power before starting work.

turn off all electric to the wall oven. removed the old broiler. replaced the new broiler and turned on the electric. checked the brolier one to see if it worked....it did thanks for the customer service for her help in finding the replacement part.

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

Took the old levelling leg out and screw the new one in.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.