Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broil (top) element burned out.
Unplugged the power supply. Took off the cover on the back of the unit. Unplugged the wires to the broiler element. Removed the bolts(4) holding the element inside the oven. Removed the temprature sensor from element and took it out. Put it all back the way it came out. Worked great. Took 25 minutes.
The only hard thing was contorting my old beat up body and joints long enuff to reconnect the 2 wires and oven heat sensor and put in 6 screws with a 1/4" nut driver. I did remover the oven door and that made it much easier for me.
Burner spontaneously cycled without knob activation
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
On the website, the heating element looked exactly the same with same measurements as the old one. However, the part I received did not match. The screw holes where the element attaches to the back were wider apart and higher. Plus, the leads curved up instead of being straight.
I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.
Make sure you turn power off at the breaker, then replace the element.
pulled range out,unplugged it,thenI removed the two screws that hold the element in place.take back cover off, then pulled the element out about 3 inches and disconnected the two wires.put new element in,put wires and screws back in place,checked to see if worked,did not work,check and reset breaker,it works put cover back on,push range in palce and done.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,
Heating element literally blew apart during use one. We have no idea why,
First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. This was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.
removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.
We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!
Bake unit caught fire and a 3 inch section burned away
Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two screws to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.
It was just a matter of removing 5 screws that attached the broiler coil to oven top. Then carefully removing coil so as not to cause wires attached to fall into the back of the oven. Needed an extra pair of hands to hold coil while i guided the wires back thru the opening. All that was left to do was to secure the broiler coil to oven. All completed in less then 30 mins. A lot easier then originally thought. And, a lot cheaper then getting a repair person to do the job.
My friend's husband came over to help. I mentioned that after unscrewing the old bake assembly unit, we would have to capture the wires or they would slip into the back. Before he even had the screws undone, the wires did, indeed, slip into the back. He then removed the back panel and retrieved the wires, pushed them back through the insulation and clipped each of them onto the back assembly. However, the wire clips kept slipping off so he eventually had to criimp the clips to keep them tight on the ends of the bake assembly. That troubled me; what if in the future one of those clips comes loose while the oven is in use? Any suggestions on how to keep these connectors on tightly?
Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
