JB710SK2SS General Electric Range - Instructions

I removed the control panel by removing 7 screws and replaced the light indicator and lens.

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.

First I searched for the part here and I had a slightly hard time finding the correct element on the site.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.

At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.

Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.

First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.

Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whipping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

Followed the directions!

Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.

Performed repair using a video for reference.

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

Replaced element control switches