HDA3400G02WW Hotpoint Dishwasher - Instructions

Followed the easy to follow instructions. Disconnected water, power, drain hose.. Pulled out unit. Tilted to back, used nut driver to disconnect motor brace, loosened hose clamps. Pulled pump/motor off. Unscrewed off defective part. Cleaned area of debris to reassemble the part ordered. Reconnect everything, reinstalled dishwasher. Turned on unit. No leaks! Dishwasher works great.

I removed the old corner tub baffle's and replaced them with the new one's and that took care of the problem. I used a putty knife to remove the old one's and put some new adhesive on and put the new ones in place and let them set up for two days to let them really set up and they work really good no leaks.

I removed the sump cover and it was disgusting! This was the first thing I did to trouble shoot. I tried cleaning the cover but it was just too dirty. I ordered a new part and now I don't have any more water pooling at the bottom. I unscrewed the cover and then screwed on the new one. It did not come with screws so keep your original screws.

Remove front shields on bottom of dishwasher. Shut off dishwasher and electricity. Unplug electric connection. Unscrew brace holder screws on front. Remove clamped on hose at back of valve. Unscrew valve from copper water pipe. Screw on new valve to copper water pipe. Put on clamped hose. Screw on bracket. Plug in electric connection.

used tips from a past buyer

whole assembly screws out, replacement was a breeze. I love this site. Parts came quick

Put rack in place and snapped new one in.

Quick and easy...a 7 yr old could have done it.

We removed old gasket, cleaned surfaces and installed new gasket.

I removed the plastic inner door liner, removed the timer assembly. Replaced both plastic parts, Detergent cup release arm and dispenser release timer lever. The most difficult part was reassembling the timer lever spring. Long nose pliers made it simple. Works like new.

Turn off the power at the breaker panel. Turn off the water supply that goes to the dishwasher. Remove the front lower panel to gain access to disconnect the water line and electric. Now remove the two screws that connect the dishwasher to the countertop. You should be free to slide the dishwasher from under the countertop far enough to remove the drain hose. Slide the dishwasher out all the way and lay on the floor door down. Loosen the two clamps that hold the motor up. Remove the motor bracket, (should only be one screw. Disconnect the wires from the motor. Now just pull the motor down and out. Repeat the process to install the new motor. I took several pictures before I started removing anything. The instruction that comes with the kit is very good. Their will be parts in the kit that will not be used. Not to worry!

I popped out the stoppers at the end of the gliders. removed broken rollers and slid on new rollers.re-installed stoppers, tested all functions. tested good

Pop out the old baffles with the help of a screwdriver, push in the new parts in their places and done.

I cleaned all the drains in the dishwasher and the drain in the garbage disposal that leads from the dishwasher. I also removed the piston and nut assembly and tried cleaning it but the dishwasher still did not drain. I was using a wet vac to empty the standing water after the cycle completed. I bought the new piston and nut assembly. It arrived in 24 hours. I unscrewed the 4 screws in the back of the dishwasher that held the screen that covered the assembly, used my hand to unscrew the piston and nut assembly, screwed in the new part and replaced the screen and 4 screws. It completely fixed the problem.

Removed rack by twisting and pulling off the plastic ends of the upper roller tracks. Removed old wheels from track and discarded. Removed old wheel assemblies from rack with fingernail. Replaced wheel assemblies on rack with the new ones. Alligned rack with tracks and pushed back into the dishwasher. Replaced plastic track ends with opposite action required for removal. Job completed.